XC8 Pragma Conifg (oridolfi)
HelloI'm using XC8 with PIC16F877 and Pickit 3. When I try to debug my program I get a message that says something like this " the device in not ready for debugging. Verify you configuration bits ..."...
View ArticlePICkit3 can't see PIC18F46K80, questions voltage, gets zero for Target Device...
We've been using PIC24F's for several years now, with a PICkit3 that works perfectly. We've done a new board that uses our first PIC18F running on 5V. When we plug in the PICkit3, we get a series of...
View ArticleTLSv1.2 support in PIC24FJ256GB206 (tushar99795)
Hi,I am using PIC24FJ256GB206 and Microchip TCP/IP stack V5.45 in my project. According stack documentation, stack only uses SSLv3 for HTTPS. I need to use TLSv1.2. Is there any possibilities that...
View ArticleAccess Denied (ggallant571)
I am getting when trying to reply to a message. Access Denied You don't have permission to access "http://www.microchip.com/forums/post.aspx?" on this server. Reference #18.eb3c7841.1392743109.449d7ad..
View ArticleProgrammer to go function can't be select (sabahan)
When I first connect the pickit 3 to the pickit 3 programming utility(Supply with the pickit 3 kit),the software report that the pickit 3 is in mplab mode and the correct OS needed to be loaded,I than...
View ArticleModify PICKIT 3 (programming speed) (victtk)
Hi everyone,i am currently student in electronic field, and for one of my project, i am using PICKIT3 programmer for PIC12F1822.However the PIC is welded on prototype with capacitors and the goal of...
View ArticleProgrammer support PIC24fj1024gb606 (Samoussa29)
Hello everybody, here are my resources : Origin device : PIC24fj256gb106 New device : PIC24fj1024gb606 Programmer : PICkit 3 IDE : MPLAB X v3.26 Compiler : XC16 v1.26 I found no answer on the forum to...
View ArticlePICkit 3 Programmer-To-Go locks occasionally locks up. (CarmineForte)
Hi All, I am using a PICkit 3 in Programmer-To-Go mode to program a PIC18F45K80 on a small board. The majority of time the Programmer works great: The Blue "Active" LED blinks slowly indicating the...
View ArticlePICKIT3-The target has invalid calibration data ....? (brian.rushka)
Using MPLAB X IDE v3.26 with PICkit 3.Device PIC10F206.Using XC8 compiler. To avoid "invalid calibration value" error, uncheck "Program calibration memory". This is found under Project...
View ArticleWindows 10 and in-circuit programming of the PIC12LF1552 (raptorsoul)
We’ve been using MPLAB and our PM3’s for many, many years. We program various chips for different purposes… PIC12C509, PIC18F2321, PIC16F636, PIC16F684, and PIC12LF1552, just to name a few. We use...
View ArticleProgrammer To Go and Code Protect (TFTtimmer)
We use the code protect bit on a PIC18F47J53 micro. Occasionally we need to update firmware in the field and send customers a PicKit3 set for Programmer To Go with the hex file loaded. Does anyone know...
View ArticleProblem with ICD3 & PIC18F46K22 (krishna velu)
I`m facing problem in programming the PIC18F46K22. when i tried to program the device it gives a error message. Target Detected ICD3Err0086: Target Device ID (00000000) does not match expected Device...
View ArticleMplab PM3 got 3 beeps and then nothing on screen (haider)
Hallo When I Start up the pm3 I get 3 beeps and than. Led orange aboven and green below. The display shows nothing. I read it has something to do with the power monitor. How can I fix this?..
View ArticlePickit3 programming cable length (hakelm)
I have a PIC16F1823 running at 4 MHz sitting in an awkward position and need to debug it in situ with a Pickit 3. Is it possible to use a programming cable length of around 1 meter? What is the...
View ArticleVdd Errors on PICkit2 Clone (Jidis)
If there's anybody out there who actually enjoys the wonderful challenges of fault finding and can spot anything screwy about this schematic, I've fought with it for a full day and will most likely...
View ArticlePickit 3 supply while in program to go (darren05)
Hi, I am programming some PCBs using the programmer to go feature of the Pickit3. I was monitoring the Vcc and Vdd pins and I noticed something strange. I am supplying the micro which I'm programming...
View ArticlePK3CMD vs MPLAB for programming (BorgLab)
I wanted to know if there was a command for PK3CMD that would allow us to code-protect some of the memory areas, similar to how MPLAB does it in the config bits. The documentation for PK3CMD does not...
View ArticlePICkit 3 as Serial Analyzer (me21)
Hello, Is it possible to use PICkit 3 in user PC application as SPI master port or as UART?I've found the same functionality in PICkit Serial Analyzer but I'm not sure if these products are...
View ArticlePickit3. Target Vdd function dead. (Andrius_Vaiceliunas)
Hi. I try project boost converter with mcu PIC16LF1508. I progamming PIC in working pcb, existing firmware was duty cycle = 50, new firmware duty cycle = 75. When new firmware writing, boost converter...
View ArticlePICkit 3 firmware question (Qual)
hi all, i am a newbie in microchip and i am learning to code PIC16F18855 using MPLab .I dont see the availability of PIC16F18855 in Pickit3 to dump my code on my board. Can anyone suggest me the...
View Article