Need MPLABX device file for PIC16F18323 (914paul)
I ordered some of these new chips then realized I don't have the device file. Does it exist yet?..
View ArticlePICkit3 / MPLABX : Why does the programm complete chip (slow) ? (DirkF)
Hello,I am working with Pickit3, latest MPLABX and XC32 compiler.In the Options I have choosen " Allow Pickit3 to select memories". My actual project is in the beginning phase, so only 5 % the programm...
View ArticleICSP failure to program while in circuit? (chopnhack)
Hello folks, like a bad penny, I am back again! I have been trying to learn abit more code using the 12F675. I built a circuit to serve as a development board for this specific chip. Why? - I had been...
View ArticlePICkit3 and Command Line Interface "Boot, Secure and General Segments"...
Hi, I am trying to use the ipecmd.jar to program the dsPIC30F5011 very similar to this . I am getting this error: “You are trying to change protected boot memory. In order to do this you must select...
View ArticlePickit3 programmer-to-go mode without MPLAB. help!!! (lucasromeiro)
hello, I need to use a programmer-to-go PICkit3 function without using the MPLAB. I need to know if you have any standaone program or something simpler to use programmer-to-go without the mplab...
View ArticleTarget Device ID (0x3fe0) does not match expected Device ID (0x2080) |...
So yeah here is my problemI have tried this with 5 different PIC16F887 and it always says the same. IPE-------------------------------------------Connecting to MPLAB PICkit 3...Currently loaded...
View ArticlePicKit3 "Failed to program device" (Benny32)
Hello everybody, I'm having a problem with my PicKit3. I've created a own circuit board with a processor board from MikroElektronika (). I'm getting the fail message that the device could not be...
View ArticleFunctions of pins in pickit 3 (lightaiyee)
Are pickit 3 pin functions similar to i2c? Can I map ICSPDAT to i2c SDA and ICSPCLK to i2c SCL? Are PDG and and ICSPDAT referring to the same function or are they different multiplexed functions? What...
View ArticleNeed to program PIC24FJ128GB202 with standalone Pickit2 (zijo)
I looked Pickit2 data file editor but only information that I can change is devices ID.For example I looked file for PIC24FJ128GB106 which should be similar, but there are values for configmask and...
View ArticlePICKit 2 pages on microchip.com totally borked! (Ian.M)
The PICkit 2 programmer page: http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en023805 and device support list:...
View ArticlePICkit 2 loses Bandgap setting of 16F630 when programming (holzwurm)
Hello, Scenario: In PICkit 2, I do the steps - File -> Import Hex - Button: Write Then PC2 seemingly performs all necessary steps, and also displays the OSCCAL and the Bandgap value. However, on the...
View ArticlePickit3 and MPLAB X, looking for a firmware load workaround (oliverb)
I have a problem with Pickit3 and MPLAB X and some computers where whenever MPLAB X needs to replace the PK3 firmware the process fails consistently. Currently my workaround is to borrow a computer...
View ArticlePICkit 3 windows 10 Connection Failed Error (Desmond_M)
Hello I have been trying to sort out a connection error problem not detecting the PIC a 16F1939 when using windows 10. I am using MPLabX V3.26. I have tried powering the target device with it own Power...
View ArticlePICkit3 not working in Windows 10 (rajbex)
I just upgraded my PC to Windows 10 and all of a sudden, my PICKit2/3 stopped working with both the Standalone Application as well as MPLAB X v3.35. The connection to the PICkit 3 is failed. Anybody...
View ArticlePICKIT 3 red light contentious on Issue ?? (sharafutdy)
Recently my PICKIT 3 was red light on continuously so the MPLAB IDE v8.89 didn't detect the device and couldn't program the IC. Anybody know the issue , Can i get the solution for this ??with thanks...
View ArticlePICkit 2, ICSP, 16F57: Programming failed at Program Memory address 0x000000...
I've connected the PIC16F57 to the PICkit2 programmer via ICSP. The attached image shows the connections on the breadboard. The only power supply is coming from the programmer, and there are no other...
View ArticlePICkit3 to In-Circuit Debugger Cabling (justinmreina)
Hi guys, I have the PICkit3 and an Olimex PIC32MZ2048 platform (PIC32-HMZ144) and have them connected to program and debug with (6) Adafruit 3" M-F Jumper Wires. This works but feels ghetto,...
View Articlepickit 3 what happend if Vdd target voltage is below 5 v (Navaneeth S)
sir, am new to this pickit 3 debugger. in our product am using external power supply of 9v adapter, but the voltage taken by the Vdd is below 5 volt,most of all boards having command as no device was...
View Article"Default" Serial Number (Ian@IESD)
I used to connect my PICkit 3 and it would show with it's Serial Number. I've no idea what I've done but it now shows the Serial Number as DEFAULT_PK3. Is there any way to reset it back to it's...
View ArticleNew PIC on PICKIT 2 and 3 (jumbo)
good morning I need to work with the PIC16F1705 and 1706 but I can not update the file with the program PK2DeviceFile.dat PICkit2 Device Editor.exe File. The addition of other CIS has always worked...
View Article