PICkit 3 Single-Supply ICSP/VLP question (nickl)
I recently ordered a PICkit 3. For Single-Supply ICSP programming/VLP, does pin 1 on the PICkit still need to be connected to MCLR/Vpp pin of the target mcu?..
View ArticledsPIC33EP512MU814 + PK3 can communicate but not program (MJBehrens)
I have been developing using a PIC24EP512GU814 and a custom pcb for the past 6 months or so without any major problems. Recently the project specifications changed so that I need to use the encoder...
View ArticlePIC16F1459 and PICKit2 - ICSP pins? (MagicMatt)
Hi,I realise this seems a dumb question, but there are two sets of ICSP pins on the 16F1459 and I can't seem to figure out which I should be wiring up to an ICSP header to I can program the chip... or...
View ArticlePart number for original PICkit2 inductance L1, 680uH. (jc40)
Hello to everybody in this forum, I would like to know if there is some BOM for the PICkit2, from which I could get the original part number for inductance L1 (680uH). Please do not point me to all the...
View ArticlePicKit 2 Vpp Voltage Error (msdgp)
Hello, I have a problem that I have never had before.Suddenly a Vpp Voltage Error message appeared when I tried to program through Pickit2. The wierdest thing is that the same pickit2 with the same...
View ArticleTarget Device ID (0x3fe0) does not match expected Device ID (0x2080) |...
So yeah here is my problemI have tried this with 5 different PIC16F887 and it always says the same. IPE-------------------------------------------Connecting to MPLAB PICkit 3...Currently loaded...
View ArticleProblem in programer to go picki3 (viniborges)
hello, already use pickit 3, and bought 2 new PICkit3 that do not work. I use the MPLAB IDE V8.92, the PICkit3 connects without problem "Firmware Suite Version ...... 01/28/90 Firmware type...
View ArticlePICKIT 3 connection problem with PC (KDN)
When I am trying to connect my PICKIT3 with USB port it's showing error. No PICkit 3 Connected After that I am trying to upgrade my PICKIT3 firmware but again it's showing error. Downloading...
View ArticleBest device for Production Programming (Jagatheesh)
We am working in PIC programming for the past 5 months. Now we are in the final stage of development. Since i am new to this field, I am not sure which programmer to use for mass production. Currently...
View Articlepickit2 don't recognize the pic16f1786 (lutherb)
only the pickit3 hardware can program it?..
View ArticlePIC24FJ256GA106 ADC problem (KDN)
AD1CON1 = 0x00E0; // auto convert after end of sampling AD1CSSLbits.CSSL5 = 1; // no scanning required AD1CON3 = 0b0001111100000010; // max sample time = 31Tad, Tad = 2 x Tcy = 125ns >75ns AD1CON2 =...
View ArticlePICkit 3 firmware question (nickl)
I finally got my PICkit 3 to work with MPLAB Xpress :) Is there a firmware option that works with MPLAB-X/Xpress that doesn't have to load a new bootloader on the PICkit when changing targets i.e....
View Articlehow to check my connection correct and pickit3 working correctly?...
i have pic16lf1828 need to upload hex file using pic kit3. but it is not detecting target correctly.it is showing error:Target Device ID (00003fe0) does not match expected Device ID (000028c0).How do i...
View ArticleAnother "Target Device ID (00000000) does not match expected Device ID...
After years of operating faultlessly with my Microelektronika "Easypic V7", I now have the dreaded "Target Device ID (00000000) does not match expected Device ID (00005500)" message from my Pickit3....
View ArticlePICKit3 programmes device but says target device is not ready for deubgging....
I have managed to use the PICKit3 to programme a PIC32MX795F512L successfully (leds blinking test...), but cannot seem to start it in debugging mode. I am new to the PICKit3, and have searched for this...
View ArticlePICkit Serial Analyzer SPI Modes (CPOL & CPHA) (feretich)
It seems that I should be able to select the SPI mode to be used by using the "clock polarity" and "sample phase" or "clock edge select" check boxes. How do I set the check boxes to achieve... Mode 0:...
View ArticleNetwork scan issue - PIC24FJ256GB206 + MRF24WB0MB - wifi_easy_configuration...
Hello,I am using PIC24FJ256GB206 with MRF24WB0MB wifi chip. I have ported "wifi_easy_configuration demo" (from tcp-ip stack ver 5.45) on this board. I am able to detect this device in remote...
View ArticlePICKIT 2 or 3 suppported IC probelm (abhinav)
Hello there! This is my forst post. I've bought a PICKIT 2 programmer. It seems it ONLY SUPPORTS "PIC" SERIES. But I need it to also support DSPIC, All MCUs , "DSP56F" 24CXX TO 93CXX(E ROMES ALL) and...
View ArticlePickit 2 Vpp no voltage show (sabahan)
I did a troubleshooting routine and the Vpp pin show near 0 volt when I press the test button,but the programs show 11.9V,also during testing of the PGD and PGC pin,when the 30KHz button is press,no...
View Articlepm3cmd problems (Alternet)
I'm currently writing a program to write firmware files (stored on a network drive) to a pm3.The problem i have run into is my workplace has spaces in the name of the main firmware storage directory....
View Article