PICKit 3 Communication Problem With Standalone programmer, etc (jcleland)
I read through this forum and couldn't find any posts that described my current problem. If this is a duplicate, I apologize. My PICKit 3 is recognized by MPLabX, I can assemble and program from the...
View ArticlePickit 2 grayed out under MPLAB IDE (Asimo)
And what does't it mean when the pickit 2 is grayed out although the pic is in the list of supported device?The pic is pic32mz2048EFH144. I am using mplab 3.15. Any idea?Thanks...
View ArticleReg:issue on sleep mode code testing with pic24 family controller consuming...
Dear Sir,I am working with PIC24fj128010 controller.I am facing problem with sleep mode routine. In the datasheet they have mentioned that during sleep mode, controller will consume micro amps only.But...
View ArticlePICKit 3 standalone firmware (jcleland)
I know this has been asked before, but I can't find the answer and I'm beyond frustrated with this hardware and MPLAB X at this point. I need to get my PICKit 3 to work with the 3.10 standalone...
View ArticlePICkit3 Transient Problem? (RWhite)
I'm building a telephone switching device and am having trouble using a PICkit3 to debug the project. I'm using a PIC18F45K22 to control a relay (5v, 30ma coil), that switches ringing voltage (80v rms...
View ArticlePicKit3 slowly dying? (sonnich2)
Hi My PicKit3 is 2-3 years old, and I use it well.At some point it started to complain, that my USB power has dropped to 4.825V and external power might be needed.My projects so far has mostly been...
View ArticlePractical advice on In Circuit Programming (oliverb)
So as a background I've been using ICP for some time using a Mikro programmer, and it is one of the old models that links the 5v USB bus voltage through to the programming connector so I've been fairly...
View ArticleWhat are my options for ICSP 5/6 pin header? (pooomah)
Hello i've thus far only used a regular 1x6 header that matches the header on the PICKIT 3 .1 inch pitch. what are my options for smaller connector on my PCB board and using an easy-to-source (ie don't...
View ArticleOld picstart plus capable of programming SST 27F512 EEPROM? (crosswinds)
Hello. I have this old Picstart plus, (i seem to remember upgrading the firmware in it). Now i need to program an eeprom for a car ECU. Would this be possible with this?..
View ArticleLooking for dos commandline programing software. (ulao)
I have inherited a PIC project that the team uses a dev board called the EasyPic. Looks to have a MikroPro chip. I'd like to program chips from dos with this board if possible. We use the PIC18F2580...
View ArticlePICKit3 with PIC24FJ256GB106- "Connection failed" error message (tushar99795)
Hi,I am not able to connect PICKIT3 to PIC24FJ256GB106. Connection is shown in attached image.It shows error "Target Device ID (0x0) does not match expected Device ID (0x10190000)". And then it shows...
View ArticlePickit3 Programmer-to-go not strict when verifying device ID (alexconway)
I have code which is intended for a PIC16F1829. It does actually fit and work fine in a PIC16F1828 (same device but 1/2 the memory) It will also fit in PIC16F1825, PIC16F1824 but they have different...
View ArticleProblem with two PICKit3's connected (kevinmiller)
I have two PICKit3's connected at the same time. One associated with one project, the other with a 2nd project. At some point this worked fine and I was able to set the working project and use the...
View ArticleStand-alone PICkit 3 operation (kirkmans)
PICkit 2 came with a program that installed an icon. I can run PICkit 2 without the IDE being open.Is there a similar program for PICkit 3? I don't want to have to start MPLAB just to program a few...
View Article"Unhandled Exception" Error in PICkit 3 Programmer (Viswak RK)
Hi, I have been trying to program a development board using PICkit 3 Programmer and everything went right till this error popped out. Using PIckit3 programmer, when i try to connect to the PICkit3, it...
View ArticleCan I prevent the Pickit3 from drawing few mA when connected? (IU8BBM)
Hello guys,I'm developing a project which need to be very low-power. The problem is that i can't monitor the power consumption (<1mA@3.7v) because, when connected, the Pickit3 draws 4.6mA from the...
View ArticleMplab PM3 got 3 beeps and then nothing on screen (haider)
Hallo When I Start up the pm3 I get 3 beeps and than. Led orange aboven and green below. The display shows nothing. I read it has something to do with the power monitor. How can I fix this?..
View ArticlePickit 2 / 3 as custom logic analyzer & signal generator (Andrew_ww)
Hi! I would like to use pickit2 or pickit3 (any of them) as custom logic analyzer & signal generator, what i can program realtime via its usb connection (intend to write my own c# library for...
View ArticleDesigning PCB with ISP for Pickit 3 (victorChavez)
I'm designing a PCB with a PIC18f2520 microcontroller, I'd like to know if I can power the microcontroller with the pickit3 since I have connected the vdd pin of the microcontroller to a voltage...
View ArticleProgramming serial EEPROMs: PICKit 2/PICKit 3? (Baker Steve)
I need to carry out a one-off program of an 24LC256. I have read the threads on this list carefully, and the PICKit manuals, but they seem to offer conflicting advice. The consensus seems to be that...
View Article