How to program PIC32MX1XX with PICKit 3 (alexandergb)
Dear friends!I've not found a lot of PIC32MX devices in supported device list of the PICKit 3.How can I program for example pic32mx150f128b ?Is it possible at all?..
View ArticleSOLVED - PICKit3 / MPLAB X IDE / 12F1840 - Target device was not found....
Hi. I just got my new programmer (PICKit 3) and i have downloaded MPLAB X IDE software. My PIC chip is 12F1840 (low power microcontroller). The issue here is that I'm keep getting the error: Target...
View ArticlePICKIT 3 UART debugging. (DogeBirdOfShibe)
Hi y'allI got a PICkit 3, and i need UART debugging. Is there any way to do that?..
View ArticlePICkit3 Issues (Jon Wilder)
Hi all. So I just recently purchased a Microchip PICkit3 programmer to replace my Microchip PICkit2. I love the PICkit2, but quite a few of uChip's newer 18F uC's are not supported by MPLAB with the...
View ArticleVoltage drop on Pickit3 (szlovak)
Is it normal that when I supply voltage from Pickit3 , then I receive on output 4.75V when it's set to 5? I measured USB voltage - 5V, voltage after U6 - 4.96, after diode D1 - 4.75. When I measure...
View ArticlePICKIT2 and 16F721, listed as supported (Jeff001)
I needed a 16F pin compatible replacement for the 18F14k22, which has some problems, but I checked the PICKit 2 supported devices and the 16F721 was listed, along with specifying on the datasheet in...
View ArticlePickit3 18F26K22 vs Pickit2 (C_Guy)
Hi, I try to use a pickit 3 with the new mplab software, but it always says target "Target device was not found. You must connect to a target device to use PICkit 3.". If I use pickit 2 programmer...
View ArticleREALICECMD: Is it still supported? Where can I get the latest install? (Lee22)
Hi, I was wondering if anyone can please tell me if the REALICECMD apllication is still supported?If so, where can I find the latest installation program for it?If not, is there a replacement...
View ArticlePIC KIT SERIAL ANALYSER WITH PIC16F (bira77)
Hi everybody !I bought a PKSA and I am trying to understand how to use that in my project. I am using PIC16F726 and PIC16F886 and want to send to my computer (in real time) the data of Mtouch pads...
View ArticledsPIC33EP512MU814 + PK3 can communicate but not program (MJBehrens)
I have been developing using a PIC24EP512GU814 and a custom pcb for the past 6 months or so without any major problems. Recently the project specifications changed so that I need to use the encoder...
View ArticleTarget Device ID (0x0) does not match expected Device ID (0xe00). (Benjamin...
hello, I have a "MPLAB ICD 3 Evaluation Kit of microchip" card, I put a PIC16F876A and send a simple program that would light a LED everything worked fine, after that I wanted to transfer to another...
View ArticleMPLAB PM3 and Linux (swmcl)
Hi, How 'production ready' is the PM3 on Linux? Is it a completely foolproof solution or are there a number of outstanding issues? There is a major cost involved so I would appreciate an honest...
View ArticleCheck the good programming PIC using PICKIT (ICDDEBUG.txt) (fishingman)
Hi,I used before the ICD2 programmer to automatically program PICs (using a developed software). I used ICDDEBUG.txt file to check if the PIC is programmed or there is an error. I wanted to know if...
View ArticlePICkit 3 can't program 18F65J11 (Waax)
Hello I've got a board with a PIC16F690 and a PIC18F65J11 on it. Both of them are powered by a 3.3V rail. To program those PICs I use the IPE V2.05 and PICkit 3 Firmware 1.30.09.I can program the...
View ArticlePickit 3 doesn't detect PIC16F1454 if Vdd under 5V (elliotwhite)
hiya, i'm using a pickit3 to program a 16F1454, there is nothing connected to the PIC except the ICSP connector , DC power connector and a decoupling capacitor.With the target Vdd at 3.3V the Pickit...
View ArticleIPECMD (JoDa)
Hi! I'm having some issues using IPECMD.jar As I have understood; on the Windows platform the pk3cmd exe is a wrapper around IPECMD.jar When I want to use the power from the PK3 this works:pk3cmd...
View ArticlePicKit 2 Firmware (Keith Sloan)
I have an old PicKit 2 that I am thinking of bringing out of retirement. Please can you advise how I can check firmware version and where I can obtain latest firmware. Thanks..
View ArticlePICKit 2 connector. (Keith Sloan)
Please could somebody tell me the name of a supplier preferably UK and part number for the connector that goes on the PCB to connect with the PICKit2. I am after one the same as the 48 pin Demo board...
View ArticlePicKit3 is not working! (fyodore82)
Hello! I use PicKit3 for about 1,5 years and it worked perfectly.Today I started to program P16F690. Before it I programmed P18F4550, so my PicKit decided to download new firmware, AP and something...
View ArticleNo Pickit3 Found (maurosmartins)
Hello all, I have been using pickit3 for some time now, but suddenly it stopped being detected by MPLAB, both Mplab V8.92 and MplabX. The pickit is working because using the pickit3 application I'm...
View Article