PICKIT3 support 16F1509? (Jontom)
I use PICKIT3 - MPLAB IDE 8.36 and I could program 16F690 successfully.Now, I want to change MCU to 16F1509, but 16F1509 is not in the device list under Configure menu. Can I add 16F1509? If it is not...
View ArticlePICKit 2 pages on microchip.com totally borked! (Ian.M)
The PICkit 2 programmer page: http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en023805 and device support list:...
View ArticlePickit3 and PIC32MX795F512L (ivans16591)
Hi,I bought recently a Pickit3 and i have install the Pickit3 v3.01 software from the archive.When i open the Pickit3 software my device is not recognized and i see that the device pic32mx795f512lis...
View ArticlePICkit 3 programming and debugging problem (sashak)
Hi. When I try programming or debugging PIC30F5011 by PICkit3, i get next error: Programming... configuration memory Address: f80006 Expected Value: 310f Received Value: 10f Failed to program device....
View ArticlePICkit2 Devicefile Editor (dougy83)
Hi Guys, I saw this thread yesterday as I was looking for a pk2devicefile file editor or something I can't actually remember (sad I know). I took it that none existed, so I wrote one: Download me:...
View ArticleHow to jump AC162049 to program PIC16F873A (Claudio Vega)
I have, ICD 3 programmer joined to AC162049 universal programming module (please see attached picture), and i need to program PIC16F873A. Questions:1) How to jump from J3 to J4 and J5 to program this...
View Articleunderstanding the operation of programmers (yasser fathi)
hello, I would like to find some source to demonstrate exactly how the programming/burning of the uc happens , I understand it mainly converts usb data to serial , but what are the specifics , and why...
View ArticleEEPROM Programming with pickit3 (char)
Could you tell me how to program an EEPROM 24LC1025? I connected EEPROM and pickit3 as the below schematic. I ran the "Write" button, and got the following error. "I2C bus Error" Please tell me the...
View ArticledsPIC30F3013 clock (FRC mode) (srinivas k)
Hello All, I am using dsPIC30F3013 controller and it is set in FRC mode(internal RC oscillator).I want to know the frequency at which the controller is operating. Is there any way to redirect the clock...
View ArticlePickit 3 - Fail to update firm (Grafi)
Hi, I bought recently a pickit 3, but it is not work. I use MPLAB IDE 8.92 and when i try to connect to pickit 3, start a download firm but not work. I get this output: PICkit 3 detectedConnecting to...
View ArticlePICKIT3 Programmer-to-go can brick PIC32 chips (Tim hutcheson)
All, After repeatedly bricking my PIC32MX795F512L's using the PicKit3 programmerand being locked out with "PK3Err0035: Failed to get Device ID" when attempting to connect, I determined that this...
View ArticlePIC24 PicKit3 can't debug (Marius van Horssen)
I'm trying to debugging my code on the PIC24F04KA200. But when i start debugging, i get the message:The target device is not ready for debugging. Please check your configuration bit settings and...
View ArticlePicstart Plus Enable Programmer error (unsupported?) (nav33d)
I am using picstart plus with Processor upgrade Module(PUM) separately purchased and installed in it. It was working fine , but few days back I connected my programmer and on enabling it gives message...
View ArticlePickit3, PMBus Stack GUI 1.4, Windows 7 or XP (Alex HK)
I have Pickit3 installed and up and running (used to program a few hundred times already) on Windows 7. MPLAB works and the stand-alone programmer. However, I have difficulties to get the PMBus GUI to...
View ArticlePickit 3 MPLABX and IPE Connection Failed (Leonimer)
I cannot connect de IPE and/or MPLAB with my Pickit 3 programmer. With MPLAB 8.6 it works perfectly. What could be the problem? Thanks, Leonimer..
View ArticleICD 3 Turn off PE (UraniumKnight)
Hi, I am trying to program a dsPIC33FJ32GP101 using an ICD 3 and MPLABX IPE. The has a programming executive, but I do not want to use it. Instead, I just want to use standard ICSP. (The reason for...
View ArticleHow to update firmware suite of PicKit3 (Dima_K)
My firmware suite version is 01.27.15. I saw messages in different forums where its version greater then mine. 01.28.92 or even 01.31.20I use MplabX 2.15 and PicKit3. Mplab does not update firmware...
View Article"Your PICkit 3 firmware version is too old" (bitluni)
Just installed MPLAB X IDE and trying to use my pickit the first time. This is what I get: "Connecting to MPLAB PICkit 3...Firmware Suite Version.....01.22.08Firmware type..............PIC18F Your...
View ArticlePK3Err0040: The target device is not ready for debugging (rocket42)
hello, everyoneI am developing application using PIC18f4620My framework: MPLAB IDE v8.70, mcc18 v3.31, and Microchip PICkit3- The first, I set pickit3 as programmer (in mplab ide, I seleced...
View ArticlePICkit 2 Programmer Software v2.61 Released (shivansh)
I have pickit2, but firmware expired. can you suggest me how to load it;s firmware..
View Article