hi, i am using pic18f14k50 and i am trying run with debug mode.i get an error that i need a debugging header.what is that debugging header?do i need this header or can i bypass it?..
↧
PICKIT3 & MPLAB X require debugging header (Alon Boico)
↧
PK2CMD for Ubuntu 13.04 and recent device files (Doubletop)
I've just had to build PK2CMD for Ubuntu 13.04. I'd never done it before but finding all the parts was a bit of a challenge as they are all over the place Before you start you need to ensure your system has G++ installed. Its in the software centre so jus..
↧
↧
PM3, 4 ICD3's, PICKit3 Failed to get deviceID (Zep.LiesNDeceptionPaintball.604)
Ok so I have been back and fourth with microchip support since the 14th every day.. and at this point I am frustrated and far beyond annoyed with this situation, so I will let the forum have its shot.. I have a PM3, four ICD3's, and a PICKit3 ALL read fai..
↧
PIC18F67k22 programmer kit ? which one ? (nowever)
Hello Guys, I'm new to microchip world so excuse me :D well i want to use a pic18F67k22 for one of my projects. and i need your help telling me which pickit should i use and what programming board do i need ? is the DV164130 working ? thank's for the help..
↧
Programming dspic33ep512gm604 using pickit2 / pickit3, getting started (danieluser)
Hi! I'm trying to program dspic33ep512gm604 using both programmers pickit2 and pickit3 and I'm stucked in place. Until now I was working with PIC18F25K80 using pickit2 to program it. Technically PICKIT2 doesn't support PIC18F25K80 but i found on the inter..
↧
↧
What programmer for serial production? (giuseppe83)
Hi to all,
I want to know which programmer is recommended for serial production.
Now for developing I used PICKIT3 and ICD 3 programmers.
But now for program a serial production of electronic boards what is the suitable programmer?
I have think ..
↧
PM3 Buzzer (mvakil)
Can the PM3 buzzer be setup to buzz when programming is complete in stand alone mode? I have a SD card with an environment but when the user programs a device there is no buzzer indication that programming was complete - It woudl be helpful to have that a..
↧
PM3 not compatible with PIC24FJ32GB004 (odingalt)
Greetings,
We are using PM3 programming unit with latest firmware update. We are unable to Program/Verify the PIC24FJ32GB004. We have tried programming by using a laptop, a desktop, and also from a FLASH memory card in stand-along programming mode. In ..
↧
PM3 environment files do not work in standalone (unless PM3 is plugged-in n' connected...) (odingalt)
Greetings;
Unable to generate valid .PM3 for stand-alone programmer use unless I am in the presence of, and connected to, the PM3 programming unit. This means I cannot generate valid .PM3 offsite and e-mail those .PM3's to my factory.
For example, i..
↧
↧
Trying to program PIC16F1455 with PICkit 2 and pk2cmd (mogen317)
Hello, I'm trying to program a PIC16F1455 with a PICkit 2 programmer and the pk2cmd tool on Ubuntu linux 14.04. However, part auto-detect fails with "No known part found" and attempting to download a hex file reports:Program Memory Errors
Addre..
Addre..
↧
PM3 power suppy cable (barber)
The connector on the cable that goes from the power supply to the PM3 has a broken pin. I have not been able to find a replacement on the Microchip site. Does any one know of a source for the cable?..
↧
Software for production programming ? (MPLAB IDE, IPE ?) (emirc)
Hi,
Which software should be used for production programming of PIC with ICD3 ?
The MPLAB IPE functionnalities suit for this, but IPE is still in beta version and it can not be installed without MPLAB X. So, is MPLAB IPE recommended for production progr..
↧
Differences between production and development programmers (aurelienr)
Hello,
I'm working on a project for a customer that request the capability to modify a table of values in memory (EEPROM or FLASH) several years after the development.
I have thought that a simple PICkit2 should be an inexpensive solution to update the ..
↧
↧
Does MPLAB X not support the PICkit 1 Flash Programmer (turbo_bob)
Its been a REALLY long time since Ive worked on anything and trying to get back into things so the last IDE I used with the PICkit 1 Flash Starter Kit was v8.36 that came with the kit. Since I'm on a new computer now I just downloaded MPLAB X and started ..
↧
PICkit3 PIC32MZ2048ECH100 memory mismatch error (SilverOT)
Hey
Hope someone can help me out with a problem I'm having with the PIC32MZ2048ECH100 and the PICkit 3. More exactly I have the MA320012 add on board wired up to the PICkit 3. I've added a 10k resistor between the MCLR and 3.3 V and connected AVDD to VDD..
↧
Updating Device Program in the Field (MacMike)
Hello All, Is there a way to update the program on a device once it has been shipped? In other words, can I use the ProgDCom or a different set of pins to provide a new program (HEX file) to existing product? I am laying out a new board, so I can add the ..
↧
PICKIT 3 problem - Target has invalid calibration data (0x00). (MartinVoss)
Hi,I am trying for quite a while now to get my new PICKIT 3 working and to program a PIC16f505. No matter whether I read the device or try to program it, I always get: *****************************************************Connecting to MPLAB PICkit 3...
F..
↧
↧
Status LED off Programmer-to-go (shayes2416)
Hello all,I have recently been having some problems in Programmer-to-go mode, for this case I am using MPLAB 8.92. basically when the pickit 3 is connected to my computer it programs fine but when I set it to programmer to go mode and then plug it into a ..
↧
Red an Yellow Status light on solid. (bitsnbytes)
I am working on a project that has a PIC32 and a PIC18 (3.3V) on separate boards. They both must work together in the end, so while troubleshooting the programs I plugged the Pickit 3 to the PIC32. The PIC32 stopped working. Troubleshooting the board I de..
↧
Pickit 3 conflicts with Logitech Unifying receiver (GastonLagaffe)
Salut,I just tried to update the firmware of the freshly recived but outdated Pickit 3 following the advice well hidden in this forum sad: .Unfortunately, the PicKit 3 is not recognized unless I unplug my wireless mouse receiver from Logitech. In addition..
↧