A: MPLAB IDE: PK2Error0028: Unable to Enter Debug Mode
B: MPLAB IDE: PK2Error0009 when selecting PICkit 2 as Debugger or Programmer
C: Where do I find documentation on using PICkit 2 as a Debugger?
D: The Debugger / Programmer option for PICkit 2 is gr..
↧
PICkit 2 FAQ (PICkit2Dev)
↧
Pickit3 Programmer-to-go error (llaplante)
Hello I use Pickit 3 many year (i have 2 ) and when i buy 2 new to put in Programmer-to-go to ship in field for firmware correction update, i found this error in Mplab 8.92: Downloading image...PK3Err0001: failed while writing to program memory.Download o..
↧
↧
PK3 ICSP Questions (CraigHB)
I'm working on a circuit for the PIC24FJ64GA202. I plan to use a PICkit 3 to program and debug. I'd like to stick with the 28 pin part, but I'm just one pin short of both PGC and PGD dedicated to the ICSP connection. I don't want to use a jumper since thi..
↧
Unable to program PIC18F26K22 using the PICKITv2. (aaa)
Is there no way to use the PICKITv2 to program the PIC18F26K22 with a hex file? on the device menu i an unable to select this chip. is there any work a rounds or down loads?..
↧
SOLVED - PICKit3 / MPLAB X IDE / 12F1840 - Target device was not found. (assafelbaz)
Hi. I just got my new programmer (PICKit 3) and i have downloaded MPLAB X IDE software. My PIC chip is 12F1840 (low power microcontroller). The issue here is that I'm keep getting the error: Target device was not found. You must connect to a target device..
↧
↧
PICKIT 3 Supported device list (mgauthier711)
I can't find a supported device list on the Microchip website for the Pickit 3. Can someone point me to it or confirm that it will program the following devices in MPLAB? 12c508A
12f683
16F84
16F884
18F252
Thanks, Mike..
↧
Target Device ID (0x0) does not match (Amarjith)
Hi, Please help me when i try to programming device i'm getting the following error. I'm using MPLABX IDE v2.15, xc8 compiler, pic16f883 microcontroller,pickit 3. PICkit 3 connected*****************************************************Connecting to MPLAB P..
↧
PICkit3 will not go into Programmer-To-Go mode (petehand)
I got a brand new PICkit3 about 12 hours ago and have spent every minute since then trying to get it loaded for PTG, without success. It works just fine as a programmer when operated manually, but I need it for PTG. I have to send it to a customer to refl..
↧
PIC24FJ128GA202 and Pickit2 (zijo)
is not on the list of supported microcontrollers for Pickit2 but wondering why? Would be programmed but some features cannot be programmed or it wouldn’t work at all...
↧
↧
Help: PICKIT3 with MPLAB v8.6 does not program PIC16F1825 (technocrate)
I have bought a clone PICKIT3 (ebay china) and tried to program two different batch of PIC16F1825 chips.The PICKIT3 does not recognize 'F1825'. As it attemts to program it, it immediately says program completed.I have tried different versions of MPLAB(v8...
↧
Controlling (any) PIC programmer with another PIC (darren05)
Hi, I'm developing a PCB functional testing equipment. During testing, the product under test will be programmed.Up till now, I used to use a pickit3 set to Program-To-Go. A wire would be soldered to the pickit's program buttonand when the equipment neede..
↧
PicKit3 - Memories to Program - Making Reservation for Flash (Patrick Best)
Hi Everyone; Working with a PicKit3 and a PIC12LF1572. I am now learning how to store data in the PROGRAM MEMORY and i suppose the first thing i have to do is to reserve a useable and predictable range for my data. My current program in MPLAB X IDE v2.20 ..
↧
PICKIT2 only program the BANK 1 - How to solve it? (l.takahata)
Hello. I have a problem I never saw in 16 years working with Microchip: I'm using the mikroC compiler and the PICKIT2 to program my board. The problem is: PICKIT2 only can write if the program is on BANK 1 (0x00 to 0x7F). If I use only one byte more the P..
↧
↧
Low Voltage Programming (chacabucogod)
Hi, I just bough a pickit, and was reading the manual when I found out about LVP. What is it? How is it used? What is it used for? I've looked on the internet,and all I can found is about how it is enabled. Thank you...
↧
PICKIT3 DEVELOPMENT BOARD (Claudio_Baldo)
Hi, I am just starting in PIC programming, doing a sample project to control a dc motor in PWM.I am having some issues with MPLAB X IDE and I am not sure why.I got a PICKIT2 2 programmer, then realized I needed a PICKIT3 due my project requires a PIC12F68..
↧
PICKIT3-The target has invalid calibration data ....? (span)
Hi
I am using PICKIT3 for programming the PIC12F508 controller .PICKIT3 is not able program the target controller. Using MPLAB IDE 8.43 and HI-TECH C Complier.
After connecting to the debugger,it gives following error
Connecting to PICkit 3...
Run..
↧
pickit 2 keeloq programmer (mstrtf)
hi. ive updated my pickit2 software to v2.6 but my problem is when i generate the .num file in mplab for say 10 devices. it doesnt give me a flag to warn that i reached end of line. in other words if i program 11 devices the last 2 will have the same seri..
↧
↧
PICkit2 Devicefile Editor (dougy83)
Hi Guys,
I saw this thread yesterday as I was looking for a pk2devicefile file editor or something I can't actually remember (sad I know). I took it that none existed, so I wrote one:
Download me: PICkit2 Device File Editor -- All versions are avail..
↧
PM3 problems programming PIC18LF46K22 (Cleverson Scharf)
Srs I tried to programm some pics 18LF46K22 using PM3, but I can´t.The PM3 don´t find an ID for PIC. I tried using power from PM3 and power from another supply.Is there some firmware upgrade? I haven´t found nothing about this on microchip site.Someone ca..
↧
PICKIT3 & MPLAB X require debugging header (Alon Boico)
hi, i am using pic18f14k50 and i am trying run with debug mode.i get an error that i need a debugging header.what is that debugging header?do i need this header or can i bypass it?..
↧