Production Programming (Eric234)
Hello, Sorry if I'm posting this in the wrong location - hopefully this is close enough. I'm trying to determine a good method (hardware and software) for programming our part (PIC16F18346) during...
View ArticlePicstart Plus Corrupt PUM (santiniuk)
Hi, Today I used my trusty Picstart Plus programmer but the labs mains supply tripped during a firmware upgrade of the PUM. Bad luck to say the least. It's quoting a corrupt firmware which is no...
View ArticleDSPIC33EP65GS804 MPLAB X program verification glitch (adilmalik)
Hi Everyone,I am having what seems like a glitch in the program-verify cycle when trying to upload code via MPLAB X IDE. I can read the device fine, and I can check that the correct device is connected...
View ArticleMultiple serial read (geoffers)
Hi all Just wanted to check this is a sensible idea, I'd like to receive serial data packets from a few temperature sensing modules I've made to a central module. I was thinking use a 16f1779 cos I've...
View ArticleUnreliable programming with PicKit2 / 18LF2685 (kelt)
Hi everybody, I have a strange situation with some of my boards.I program the installed 18LF2685 with my PicKit 2 and everything looks OK.The program runs perfectly. No issue at that time. But some...
View ArticlePicstart+ Unsupported programmer (LuxARTS)
Hello! I found an old Picstart+ R13, I opened it and it has the flash upgrade module. I downloaded MPLAB 8.56 (I saw that MPLAB X doesnt support picstart+) but when I select the device and try to...
View ArticlePicKit3 not recognised in MPLAB X 5.45 but seen in IPE (sjb741)
Coincident with acceeding to the MPLAB 'Updates available' box (I don't know what they were, I just assumed it knew best...) then my PicKit3 (genuine) is not shown in MPLAB X. In Project Properties,...
View Article18F452 NOT DETECTED BY PICKIT 3 (elec.nas)
hi ; i'm trying to program the PIC 18F452 by PICKIT 3 ,using the software MPLAB V6.48 but it seems that the PICKI3 cant't detect the device (i have this messaege( DEVICE NOT DETECTED ),in fact i'm...
View ArticleMPLAB PM3 P/N 10-00359 does support 64-bit drivers ... (eatlp)
Hello ... I am hoping someone will be able to help me.I have an old PM3 programmer which we use for programming in our production line.I was in the process of adding another program for a new PIC &...
View ArticlePIKit 4 Causes EE writes to fail after EE bulk erase (yeags)
Issue: I have a function that block erases EE and then copies new data to EE. This has worked fine for several years until I switched from a PK3 to PK4. With PK4 reading back and viewing EE data shows...
View ArticleHELP! Cannot program PIC16F688 with PICKit3 due to code protection?...
Hi, I had successfully program a brand new PCI16F688 firmware. Now, I'd like to reprogram it with a new updated firmware, it keeps failing to program at address 0x0000. I figured it's probably because...
View ArticlePIC12F675 - Using ICSPDAT/ICSPCLK pins as GPIO pins (lukegalea16)
Hi, I need to connect the circuit shown below to ICSPDAT or ICSPCLK. Is it safe to do so? Or will it affect programming?Thanks!...
View ArticleSet security bit (SSB) in samd51 using pickit4 (ANOM)
For ATSAMD51, how can the set security bit (SSB) enabled from Pickit4 as an independent step after flashing the firmware? Due to some code development restrictions I cannot make this part of the main...
View ArticlePICkit3 and Topsee (naeem1234)
Hello everyoneI have bought PICkit3 from a local vendor. It has 'Topsee' logo on its back which is a chinese website.I wanted to know is it the genuine Microchip PICkit3 or china copy?I wanted to flash...
View ArticlePICKIT 3 and PIC16F628A (Billiam)
I am trying to write a new hex file to a pic16f628a with no luck. The pic is already soldered on a circuit board but the board also has the five ISCP pads and I verified they go the the correct pins on...
View ArticlePICKit3 and PIC32MK? (Georgy)
Hello! I have several PIC32MK custom boards with blink LED flashed and need to re-flash them with Harmony 3 bootloader. Is it possible to perform it with PICKit3? Thanks..
View ArticleIssue with programing PIC18F67K22 past memory location 14000 (markdem)
I am having some issues programing a PIC18F67K22 using a PICKIT3.Programing will work fine until the program grows and passes memory location 14000, at witch point I will get the following...
View ArticleTroubles reading code from dsPIC30F4011 (ndemarco)
I'm using a genuine PICkit3 and MPLab X 6 to read a dsPIC30F4011. The reading process completes normally per the IDE, but the program memory OPCODEs are all 0xFFFFFF. I watched the PGD and PGC lines...
View ArticleHow do i program 8 bit PICs now (onload)
Hi,I always used to use Pickit3, but its obselete now?....how do we cheaply program PIC micro's now?..
View ArticleCan a PIC32MZ2048EFM144 be programmed with PicKit 4 programmer? (Stellae Tempus)
Dear everybody. I am going to receive sometime some PIC32MZ2048EFM144 chips. Will I be able to programm these microcontrollers connecting them directly (no adapter / breakout board) to my PicKit 4?...
View Article