Pickit3 Devicefile Editor (tibe02)
I have to create a new part list for PIC24F08KL301 in the "PK2DeviceFile.dat" with Device Data File Editor. Someone can tell me the values ​​to be included in the file. Thank you very much.
View ArticleProgramming of PIC16F1503 (npelov)
One of the major advantages microchip offers over it's competitors in hobby electronics is PICKit series programmers that can program the (almost) whole rage of microcontrollers. I tried programming...
View ArticleFailed to program a device (sravan_494)
Hi, I am dsPIC and I am programming it with PICKit3 but the fallowing error is coming. please give me a reply what could be the problem and give me solution. Conn
View ArticlePickit2 and PIC24F04KA201 (jennyg)
Hi, I have a PIC24F04KA201 and I thought that I would be able to program it with the pickit2 ( However, when I open a select this device in the MPLAB IDE I cannot choose the pickit2 programmer. Is...
View ArticlePIC32MX support for PICkit 2 (timijk)
Hello, After working on the (and Thx to TrevorW and scasis), I created a device file in XML format for the PIC32MXs. The program will look for PK2DeviceFile.xml when it loads the PK2DeviceFile.dat, and...
View ArticlePICkit 2 VPP voltage level error. (drusteeby)
Hi everyone, I am currently trying to program a DSPIC33FJ128MC using the PICkit 2. All was working fine up until a few days ago when everything stopped working. When I start up PICkit 2 v 2.61 it gives...
View ArticleConnection issues from PICKIT3 to PIC18F67K90 (hoser1000)
I am trying to connect to a PIC18F67K90 with my PICKIT3 programmer and keep getting the "Target Device ID (00000000) does not match expected Device ID (00005100)" error. I have swapped out the original...
View ArticlePICkit 2 Programmer Software v2.61 Released (PICkit2Dev)
PICkit 2 Programmer version 2.61 has been released and is available for download on the PICkit 2 page here. This versi
View ArticleDevelopment tool to allow in-circuit test/coding? (DCE1511)
Hi, I have a newbie question, and would appreciate any help anyone can provide. I have been looking to purchase development tools for Pic Micros (specifically 16F84), but am struggling due to my...
View ArticleProduction programming using pogo pins (jvoytovich)
I'm looking for information on materials and construction of production fixtures for programming PIC controller boards. I plan on probing test pads on the bottom of the board with press-in pogo pins...
View ArticlePIC16F1503 programming and hardware debugging (primos)
Hi I would like to know what (apart from ICD 3 or PICKIT 3) hardware do I need for programming and hardware debugging of PIC 16F1503? On official pag
View ArticleProgramming a PIC18F26j50 with PicKit2 (ktmpal)
I have a PIC18F starter kit and I have a custom board with a PIC18F26J50 (I have routinely build boards with PIC18F1330 parts and had no problems). When attempting to program the custom board with a...
View ArticleDoubt with Pickit2 can program dsPIC33FJ256MC510A ? ( Listed only...
Hi guys, i have a pickit2 and i want to purchase a dispic33 for a quadcopter project, i was searching for some dspics and i found dsPIC33FJ256MC510A, but in the selection list from pickit2 software i...
View ArticleProgramming HCS412...a legend... (Rebound)
Hello! i am newbie on this forum, i have found it a few days ago and i am hoping that you help me... I have found discussions on a read/write HCS412 but alls without any reply... I need to read and...
View Articleconfiguration word (aswin_ajayan)
hi, i am a newbie , i have little experience with 16f. but i had to change to 18f forits hardware muliplier please anybody please tell me about the configuration word of 18f4550. atleast suggest me...
View ArticleField programmer that can load from PC without MPLAB (orbitcoms)
Can source code be loaded into PICKIT3 by alternate utility instead of MPLAB? I want to send a programmer to someone and code for 2 projects. I see you can pre-load with 1 file but not 2 and I would...
View ArticlePICKit 3 and MPLAB X - No debug (Sid723)
I just upgraded from MPLAB 8.76 to MPLAB X and I have a PICKit 3 that I purchased last year that I also used with MPLAB 8.76. I can download a simple program to a PIC16F628A with no problem. I would...
View ArticleUSB Bootloader for PIC18F27J53 (Scotty22)
I'm a newbie to this forum, but have developed several stand alone microprocessor embedded systems in a past life (Dallas Semiconductor Flip-Stik). I have an application that will require a PIC18F27J53...
View ArticleProgram memory at Pickit2 GUI (Frimmy7)
Hi all, does anyone knows what does this program memory means in pickit2 Programmer GUI? Is this the flash memory data addresses and values written on it or others else? Does the left most row with...
View ArticleMotor Driving Cycle logic error "CCS C CODE" (rhnrgn)
Hello Friends, I want to drive my motor driver with pic16f1826 with digital pulses. I want to drive it in to secitons. First section is walking, it is a little bit slower then running mode. After a...
View Article