PICKit 3 programmer and .bin files (koce)
Hello there, I'm a newbie in the world of PIC micro-controllers. I currently have a PICKit 3 programmer and MPALB X IDE installed on my computer. Is it possible to use a .bin files (for eeprom and...
View ArticleIntermittent 18F2431 (Camerart)
Hi,I'm getting problems with PIC 18F2431. I have one that works most times, and app 4x others that don't. My question is: If I READ the HEX file from the 'working' one then WRITE the HEX file to second...
View ArticleHow to burn program into 18f4550 (szacpp)
Hi,I made usb joystick program in MicroCPro. How do I burn the program into pic18f4550?..
View ArticleDebugging Error (TucsonDon)
I have an EasyPIC v7 board with a 16F1459 chip on board connected to a PICKit3. When I try to enter into debugging I get an Programming/Verify complete The target device is not ready for debugging....
View Articleanother pickit 3 trouble connection (atica agua)
hi this is andreu from barcelona .. here a question: my new pickit3 is detected by the pickit programmer when i check the communication (only when a push in this button not by default) and shows me a...
View ArticlePicKit3 support for PIC18F97J94 (xpolhecx)
Hello I bought PicKit3 programmer and currently using standalone software that I found on Microchip website. Unfortunately I cannot find PIC18F97J94 on device list. Is this normal? I prefer this...
View ArticlePikit2 programer configuration bit issue (ismailpp2008)
hi Am using pikit2 programer to program dsPIC30F2010 , in my HEX file in configuration words i already kept in code prottrcted mode , but when am loading Hex file to pikit2 software , which config...
View ArticlePICKIT3 Programmer-to-go can brick PIC32 chips (Tim hutcheson)
All, After repeatedly bricking my PIC32MX795F512L's using the PicKit3 programmerand being locked out with "PK3Err0035: Failed to get Device ID" when attempting to connect, I determined that this...
View ArticlePickit 3 doesn't preserve EEPROM in "programmer to go" (isgoy)
I would like to use Pickit3 to update the firmware of some controllers of a client with "programmer to go" feature but it doesn't preserve the configuration saved on EEPROM memory. Why? It's a useful...
View ArticlePICKIT3 problem 16F88 (Nailton)
I bought this week one PICkit3. I was recording a 16F88 and I am with the following problem: After recording the 16F88, clean the "program memory" and ask to read the contents of the recorded PIC16F88,...
View ArticleDoes anbody got PICkit2 working with PIC32MX1xx/2xx (bertc3p0)
Hi, I'm trying to get my PICkit2 working with a PIC32MX150F128B using a slightly modified 'pk2cmd' under Linux:pk2cmd -?V Executable Version: 1.21.00 Device File Version: 1.63.148 OS Firmware Version:...
View ArticleProgram memory is not blank (tpham)
Hi All, I am testing the pickit 3 and I got the "Program memory is not blank" message, anyone know what this means?The complete message is shown here:...
View ArticleUsing PICKit2 to program PIC32MX170F256B (TrevorW)
Hi, I have successfully programmed several PIC32MX1XX/2XX variants using timijk's modified PICKit2 application (which loads correct PE). However they were all limited to 128KB Program flash memory...
View ArticleMCLR reset circuit for ICSP (jack33)
Will the circuit in the attached schematic work OK for reset? The circuit is to be used for ICSP. The Schottky diode is for isolating the rest of the circuit from the programming voltage (Vpp). I read...
View ArticleIssues with Programming PIC16LF1618 using PICkit 3 (aruntkkumar)
Hello, I am trying to program my PIC (PIC16LF1618) at 1V8 using PICkit 3. I was able to do so for a couple of times. However, when I try to code the PIC at 1V8, I am getting the below mentioned error....
View ArticlePICkit3 updates? (wnovin)
How does one update the PICKit3 to program the newer chips, specifically the PIC12F1571 The chip web page indicates that this is a usable programmer...
View ArticlePickit 3 "connection failed" after upgrading to Windows 10 Pro (Tabur)
Hi! First of all, I'd like to explain the state of things here at the shop: Turmoil, desperation and anguish. Imagine fires, paper flying and everyone running with arms flailing in the air. Now that...
View ArticleHow to differetiate between two Pickit3 connected on the same PC (Zouaghi)
Hi to all,i use two pickit3 connected in the same PC, for an industrial application,each time, i have to control one of them,i use command line in order to command them, so what to do? thnx for any...
View Article16F628A endures 3 programming cycles then out of order (rikotech)
Hi all,I am using pickit 3 and MPLAB IDE to program my PIC16F628A. When I program it 2-3 times and then the device is not recognized by the programmer:Target Device ID (00000000) does not match...
View Article