mistake in lesson 12 "Table look" of PICkit3 (lip01)
In lesson 12, named „Table lookup“, shipped with the PICkit3 Starterboard, is one mistake. If you try to use this lesson (in assembler), the result will be nothing: no led is lightening, no changing of...
View ArticlePICkit 3 and Mac OS X El Capitan (redxef)
Hello, So, it seems that PICkit 3 doesn't work on OS X El Capitan (Doesn't even show the serial number). I need to start programming my chip in about a week and was hoping for some help. EDIT:So, I...
View ArticleNeed standalone solution to program pic32MZ with SQTP serial number. (MKC)
Hi,I need a solution for a standalone programmer for PIC32MZ with SQTP serial number.If not possible, best solution with minimum software installation on Windows PCAny idea appreciatedMarc,..
View ArticlePIC is restarting unexpectedly (flx_ml)
Hello, guys. I'm using a PIC16F1823 with Timer0 for now. I'm trying to control the LED's with a simple button. I use the Timer0 to verify the period of time that the button is pressed. The problem is...
View ArticleError: Target Device ID (0x0) does not match expected Device ID (0xe20) (sphari)
Dear all, I am using PICKIT3 for programming PIC16F877A DIP micro controller chip. I am using custom made programming board for programming PIC 16F877A. I am using same programmer and customized board...
View ArticleMPLAB PM3 Problem with holding the device in reset (Bobybul)
Hello, I bought a MPLAB PM3 programer and found out that I can not hold in reset conected PIC from MPLAB X 3.0. There is indication for comunication between MPLAB X and the programmer, but Vpp/MCLRE...
View ArticleImplications of upgrading to Windows 10 (SGHughes42)
At the moment I'm resisting upgrading to Windows 10 until things settle down but I am intending to do so in the next month or two. I've read that there are issues with both PICKit2 and PICKit3 under...
View ArticlePICKit3 - what new? (YANN)
Hello. Please, I need a diagram that shows how to connect PICkit3 with the eeprom for programming. question: Thank's!..
View ArticlePICKIT3 Programmer-to-go can brick PIC32 chips (Tim hutcheson)
All, After repeatedly bricking my PIC32MX795F512L's using the PicKit3 programmerand being locked out with "PK3Err0035: Failed to get Device ID" when attempting to connect, I determined that this...
View ArticlePICKIT 3 - Unable to run it as a debugger (Rakesh H)
Hey,I am using Logic Power's PICKIT3, It programs well but does not debug. I get the following message/error in the debugger console. "Launching Could not connect to tool hardware: PICkit3PlatformTool,...
View ArticlePic kit 3 basic questions (wdsvd)
Hi, I have been reading about pickit3 (I am about to buy it), and I have a few questions.- Can I perform a serial communication between my computer and the pic using MPLAB X IPE and pickit3? I would...
View ArticleCannot program PIC16F877a :Target Device ID (0x0) does not match expected...
Hi,I was trying to program pic16f877a using Pickit 3, but with no success. I am getting an error message :" Target Device ID (0x0) does not match expected Device ID (0xe20) ".I have verified all the...
View ArticlePICkit 3 strange problem (viki2000)
I use the PICkit 3 programmer since 2-3 years and works good.Yesterday I worked with it and I programmed PIC18F4550. Today, on the same setup, did not work anymore, giving the error below....
View Articlemplab_ipe didnt find pickit 3 (schlabs)
Hi, I am frustrated, i read all that i can find about pickit 3 comunication and no success. I am running an Linux 64 opensuse 11.0. I am using SUCCESSFULLY the following programers:Picstart plus (...
View ArticlePickit 3 "connection failed" after upgrading to Windows 10 Pro (Tabur)
Hi! First of all, I'd like to explain the state of things here at the shop: Turmoil, desperation and anguish. Imagine fires, paper flying and everyone running with arms flailing in the air. Now that...
View ArticlePM3 verify error on 12F1571 (dj41354)
I have a hex file that in-circuit programs a 12f1571 perfectly when using a ICD3. I used MplabX IDE v2.10 to assemble the files, and IPE v2.10 to program using ICD3 with no issues, and programmed parts...
View ArticleWhy PICKit3 is not a production programmer (LeoJiang)
I am going to integrate PICKIT3 to a test fixture to perform in-circuit programming for production board. I prefer a programmer without PC.But the user's guide of PICKIT3 said:The PICkit 3 is NOT a...
View ArticleHow to differetiate between two Pickit3 connected on the same PC (Zouaghi)
Hi to all,i use two pickit3 connected in the same PC, for an industrial application,each time, i have to control one of them,i use command line in order to command them, so what to do? thnx for any...
View ArticleProgram PIC18F device with .hex and .bin files (koce)
Hello guys, I have a .bin and .hex files that I want to load into my PIC18F2480 device. I also have a .doc files explaining how to configure PIC18F2480 before programming. I've been told that it is...
View ArticlePICKIT3 Detected but can't be connected ! (Marshall)
Hi Friends !I open MPLAB IDE for a new pickit3,From pull down Programmer Menu, I select the Pickit3.then,The IDE show Pickit3 detected !Connecting to PICkit 3 ... at the left bottom of screen, the...
View Article