PICKit 3 with MCLR as GPIO (Lotharyx)
Hi,I was just wondering if it's even possible to use the config bit that sets the MCLR pin as a GPIO (RA4) when programming with the PICKit 3. I have my config bit set to disable MCLR:#pragma config...
View ArticleExecute commands using Pickit 3? (Tabur)
Quick question: Is there a way to input and execute instructions using a Pickit 3 ICD right after a breakpoint? Maybe it's a bit stupid what I'm saying, but it would be amazing if you could use MPLAB X...
View ArticleUSB Driver for MPLAB PM3 (Durite)
I have installed MP X IDE 3.05 IPE, but cannot seem to find the drivers for the PM3, I have also tried installing the IDE as well but still no drivers seem to be present. All the searches I have done...
View ArticlePickit3 and PIC18Explorer Board (ironandalchemy)
Is Pickit3 compatible with this board? The user guide (51721b) mentions nothing about using PicKit3, and I would rather not buy ICD2 to start working with the 18F87J11 mounted on the PIM. If it is...
View ArticlePICkit3 not recognized by MPLABX 3.05, Windows 8.1 x64 (jstanle1_home)
Hello --I've been working successfully with MPLABX 2.2 and PICkit3 in Windows 8.1 for some time. I've just upgraded to MPLABX 3.05 and it doesn't recognize my PICkit3. In the project properties under...
View ArticlePickit 3 "connection failed" after upgrading to Windows 10 Pro (Tabur)
Hi! First of all, I'd like to explain the state of things here at the shop: Turmoil, desperation and anguish. Imagine fires, paper flying and everyone running with arms flailing in the air. Now that...
View ArticlePICkit2 v2.61 software and PIC12F1822 (nur53)
As I intend to load the program into PIC12F1822 using PICkit2 with v2.61 software I receive the message "Unsupported Part". Is there any newer version of v2.61 which supports PIC12F1822 ?Thanks and...
View ArticleNeed to program PIC24FJ128GB202 with standalone Pickit2 (zijo)
I looked Pickit2 data file editor but only information that I can change is devices ID.For example I looked file for PIC24FJ128GB106 which should be similar, but there are values for configmask and...
View ArticleOdd behavior in pickit3 (debug vs. release) (autx790)
I'm using a pickit 3 to program a pic18lf25k50 on the back of the RN4020 pictail card. My code works perfectly in debug mode every time. When I go to release mode, it only partially works; however,...
View ArticlePM3 behaviour! (tpicon)
Hello everybody, I am facing strange situation with my PM3. I have a board with PIC16F1939. When I try to program using my PM3 I get an error: "PM3 is unable to read device and get stuck in this phase"...
View Articlemdb.sh regression with MPLAB X v3.05 on OSX (akohlsmith)
I had great success with an earlier version of MPLABX (I think it was v2.something, sorry I don't recall the exact version). mdb.sh worked great with the "set system.disableerrormsg true" to disable...
View ArticlePICkit 3 Debug not working. (edbfmi)
Hello all,I have been pulling my hair out over this one.I am trying to debug a design that uses a PIC16F716 micro.First the basics:I am using a computer with Windows 7 Professional.I am using the...
View ArticlePicKit2 Download (jwells)
Computer crashed and had to reload the software. Can't seem to find the latest PicKit2 software. Can someone point me the right direction...
View ArticlePIC16F877A unstable performance after programming (sphari)
Dear all, I have written a program in MPLAB IDE using XC8 compiler for PIC16F877A microcontroller. I have used PICKIT3 programmer to program controller chip. My program is running well in the board...
View ArticlePower for PIC PK3 (driveguy)
I have a small circuit I'm designing and it will be self powered. I'm putting a header on the board so I can in circuit program the chip (PIC12F1501). If I externally power the chip what pins on my...
View ArticlePIC10F200 OSCCAL Invlid Value detected (zimpic)
I am trying to write my hex code to my device and I Keep getting the above warning and failing to write code to the device. I would really appreciate some assistance to resolve this..
View ArticlePICKit 2 pages on microchip.com totally borked! (Ian.M)
The PICkit 2 programmer page: http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en023805 and device support list:...
View ArticlePickit 3 not shown in MPLAB IPE v3.05 tool list (Raphy)
Hi ! I am currently working on a personal project in my spare time wink: I use a PIC 10F200 with a Pickit 3 programmer, but I have an issue to program my PIC. As you can see on the next picture, there...
View Articlepartial progrmming wanted (piccandies)
I am using a large 18F part with XC8 in MPLAB x. Right now the code only takes about 2% of the space, but programming the chip takes forever...wait...wait...wait....Is there any setting to just allow...
View Article44-pin Demo board (P18F45K20) that came with the PICkit3 dead or alive???...
I am trying to determine if my 44-pin Demo board (P18F45K20) that came with the PICkit3 is working. I am having a hard time finding any example code much less a tutorial. I have MPLAB X IDE loaded (as...
View Article