Pickit3 programming without internet connection (MitYeltu)
Ok, I have the pickit 3 and I have to program several different pics in the field: 18f4550, 18F2525, 16F1779, and my personal favorite, 18F452. Here's the problem. Where I'm going, there will be no...
View ArticlePICkit 2 not detecting target Vdd (jodyflorian)
I'm using a non-clone PICkit2, programming a PIC16F57 with ICSP. It works when I use the PICkit 2's power, but not when I use an external 5v source. If I isolate the circuit from everything (except the...
View ArticleAnother PK3 "Connection failed" on OSX thread. (Jack_M)
Hello.I have recently done a clean install of OSX Yosemite on my macbook..Of course, i installed JAVA before installing MPLAB X. The IDE works as it should but when it comes to programming it doesn't...
View ArticlePICKit3 Error PK3Err0033 (JBear)
Hi, I tried to program so PIC24FJ64GB002 processors using MPLab8 but it didn't work. I used the PICKit 3 v 3.10 and it work great, except at the end of each run I get PICKit3.ini access denied. The...
View ArticlePickit3 error while programming dsPIC33EP512GP502 on MplabX IDE and IPE v1.40...
Hello guys,i'm programming a dsPIC33EP128GP502 without any issues, it works perfectly and it seems to be perfectly supported, recently I switched to a dsPIC33EP512GP502, and I noticed that, not only...
View Articlepickit3 error (error 0005, connecting, ... OMGGG) (Brutto)
hi all, yesterday i was programing a demo board with pic18f45k20 with pickit3 on win 7 without problems, but today i will try to program dspic33... it was doing problems,... so i will try to connect to...
View ArticlePickit 3 programming speed (vs pickit 2) (VincenzoV)
Hi allIn the past I used pickit2, now i'm using pickit 3I'm now testing PIC18F26K20 (64K device) and MPLAX 3.05 under linux. Pickit 2 require about 5 second from click to running (very small) test...
View ArticleUsing PICkit2 (PICHANK)
We are starting a project using the PIC16F630 and the PIC16F1459 for a simple HID USB data transfer.The 16F630 uses ports RA0 and RA1 for serial programming. However, the 16F1459 uses either RA0 and...
View Articleprogramming 16F628 - 648 (OsvaldoH)
I need to re-program in circuit a PIC16F648AIt uses internal 4 MHz clk - internal master clear and code protection. There are all ports used as in/out.With ICD2 , a warning arises about it is not...
View ArticlePickit3 problem with MPLAB X IDE (tommycc)
When I use MPLAB X IDE v3.00 and PICkit 3 It appeared "The programmer could not be started: Failed to program the target device"and I measured with oscilloscopethen I find Vpp didn't have...
View ArticlePICkit 3 EUSART Glitch (itdontgo)
When debugging I get an occasional glitch sending data from the internal UART on a PIC16F1.It's hard to detect and I've concluded it's simply due to the PICkit 3. Would this have any affect of the UART?..
View ArticleA daughter board on the ICSP connector. (George Towler)
I have several diagnostic daughter boards that "plug in" to the ICSP connector. It works very well, utilizing otherwise unused pins (I have never been happy with the various circuits to isolate ICSP...
View ArticlePICKit2 Device File, add PIC12F1572 (ee_martin)
Folks,I have been trying to add the PIC12F1572 to version 1.63.146 of the PICKit2 Device File using the PICKit2 Device File Editor (thanks to whoever wrote that!). I have used several similar PICs as...
View ArticlePicKit3 Version 3.10 open and use normally But Can't Close it (kaemon)
Please recommend me !..
View Articlemistake in lesson 12 "Table look" of PICkit3 (lip01)
In lesson 12, named „Table lookup“, shipped with the PICkit3 Starterboard, is one mistake. If you try to use this lesson (in assembler), the result will be nothing: no led is lightening, no changing of...
View ArticlePicKit3 "Failed to program device" (Benny32)
Hello everybody, I'm having a problem with my PicKit3. I've created a own circuit board with a processor board from MikroElektronika (). I'm getting the fail message that the device could not be...
View ArticleHow to load program on PIC18F66K80 using pic kit3 programmer application beta...
Hi all, I need to load my .hex file to pic18F66K80. In pic kit 3 programmer application beta version, in devices list i have not found PIC18F66K80. So any one tell me how to add new devices in the...
View ArticlePICKIT2 (AlexShum)
Hi.I'm Alex.I downloaded PICkit 2 Device Data File Editor and I can not add pic18f87k90.Please, tell me how to do it.Thanks..
View ArticleICSP in parallel with one line jumpered? (CCP1CON)
Hi Folks, I do have four identical PICs on a board and four ICSP sockets. One for each PIC. Now my idea is to limit this to only one ICSP socket for the whole board. To achieve this I plan to connect...
View ArticlePicKit3 - Memories to Program - Making Reservation for Flash (Patrick Best)
Hi Everyone; Working with a PicKit3 and a PIC12LF1572. I am now learning how to store data in the PROGRAM MEMORY and i suppose the first thing i have to do is to reserve a useable and predictable range...
View Article