Not sure why, but after a successful program the device is held in reset requiring the PICKit 3 to be removed from the device to allow it to operate. THis can get very annoying and I did not encounter this issue in and MPLAB X version prior to 5.0. Is the..
↧
MPLAB X 5.0 and 5.1 Holding PICKit 3 project in reset after succesful program. (dwhoffman)
↧
Pickit3 not releasing reset in PTG mode (picTiger800)
Using MPLABX 5.10, pickit3, PIC32MX470F512H. If I run the program using MPLABX, it will run. MCLR is high.Set the PICKIT3 to PTG mode, and program using the PICKIT. The MCLR remains low.If I pull out the programmer it runs as expected. Does anyone know wh..
↧
↧
PICkit3 connection issue (AMPS)
I am using PICKit3 .when i connected to PC without any hardware USB is recognized . power led-green , active -> blue, status -> RedIf i connect hardware USB fail to recognize.Is my pickit3 got damaged.It wont allow me to program..
↧
Pickit3 MPLABX5.05 / Programmer to Go / Preverse EEPROM (Fausti)
Hello,Have installed MPLABX version 5.05 and was surprised, that noe the function "Preverse EEPROM" should work, because the comment "not available with programmer to go" was missing. But when I try to download the program to my Pickit3, the errror messag..
↧
PIC32MX470F512H is not recognised in Pickit 3 but seems ok in MPLabx (quagmire)
The Device PIC32MX470F512H is not recognised by Pickit 3 and is not available in the Manual Selection Either - it stops at PIC32MX460xxxx. Any Ideas Why ?..
↧
↧
PICKit3 works in Windows but not Linux (stantheman286)
Hi all, I've been reading through the forums (lots of great help!), but so far I haven't been able to resolve my issue. I have a PICKit3, which I've previously used in MPLAB X on Linux about a year ago. I'm now trying the latest MPLAB X version (v2.05) on..
↧
PIckit 3 works on Windows but not on Ubuntu 18.04 LTS (64-bits) (olaoni)
Hi All,I have Pickit 3 that works fine under Windows OS but not under Ubuntu 18.04 LTS. I really do want it to work on the Linux as this is my main development platform. When I press the debug button I get the error message "Connection Failed."I can see t..
↧
6lowpan Clicker board (quagmire)
I have a "MicroBUS" 6lowpan Clicker board. PIC32MX470F512H device. For Harmony is there a target board configuration available somewhere?Or perhaps an equivalent / close match that can be used. See https://www.mikroe.com/clicker-6lowpan TIAQ..
↧
MPlab PM3 programming dsPIC33EP64MC204 ID Memory Errors problems (luka259)
Hi I'm using MPLAB X IPE 5.10 and MPLAB PM3 programmer to program dsPIC33EP64MC204. I'm having trouble programming and am getting the following error: "PM3 Versions Details MPLAB OS Suite Version .............. .....81.18.55 BIOS Version ...................
↧
↧
PIC16F15313 with Picstart Plus2 (vinyl_theif)
Hi all.I was about to use the trusty old PIC12F508A for a 'quick' project that needs 6 output pins to control LED's on a model police car but Grrrrrrr unfortunately RA3 can only be used an input pin! I've since found the PIC16F15313 will be ideal - albeit..
↧
PICKIT3 and dsPIC33EP512GP806 (StarKnight)
Hi, I have acquired a PICKIT3 after I understood that PICKIT2 wouldn't program the dsPIC33EP512GP806. After reading several posts and trying all sorts of updates, I still cannot see the dsPIC33EP512GP806 in the standalone version of the PICKIT v3.10. Is t..
↧
PICkit 2 loses Bandgap setting of 16F630 when programming (holzwurm)
Hello,
Scenario:
In PICkit 2, I do the steps
- File -> Import Hex
- Button: Write
Then PC2 seemingly performs all necessary steps, and also displays the OSCCAL and the Bandgap value.
However, on the PIC (a 16F630) the bandgap value is always set t..
↧
PICKIT 3 unable to program (aman111)
Hi Everyone,I am using Pickit 3 to program PIC16F1503 microcontroller
MPLAB x ide v5.10
Win10 I was able to program the target earlier but now it only gives this error *****************************************************
Too much current has been draw..
↧
↧
PICkit3 failure. (peterg1000)
For the second time time my PICkit 3 has failed. Symptoms are that it fails to read the target chip identity in spite of a satisfactory self check - exactly what happened to the first one a couple of years ago. A borrowed one works perfectly, so the targe..
↧
I have 4 broken PICkit 3, should I throw them? (eagle1)
Hello, Last semester I was working on basic microcontrollers course which we used to connect the PIC with the PICkit 3 on a breadboard. But due to some faulty connections to the power and ground I used to loose PIC chips along with the PICkit 3 as well. I..
↧
Pickit 3 Connection Failed when debugging (AcePeach)
Hi, I wrote some codes in MPLABX IDE and wants to debug is using the pickit 3. My pickit 3 is connected to a PIC18F4550. I read the guide for pickit 3 and tried to do the debugging. However, when i pressed the debug button, the build was successfully and ..
↧
Pickit2 unable to detect device (Kspowertronics)
Do pickit 2 support 16f722A device? My programmer is not detecting this IC...
↧
↧
Problem trying to connect my pic16lf1825 to my RFM119 (aleix20)
Hello guys I'm fairly new to this programming microchips world, see I have a program that reads and writes from/to an EEPROM on a 16lf1825 PIC and I need to send the data to an external antena using a RF protocol (got a RFM119 chipset), but I'm not really..
↧
Corrupt image ? Do I need a extra Pickit3 ?? (cinnober)
Hi..totally newbie here.Bought a Pickit3 from wish.com which is probaly a clone of the original PickIt3 (have realized that now since there is no Microchip logo on casing and can´t find ant serialnumber/modelnumber etc. on PCB) Haven´t be able to program ..
↧
PICkit 3 + PIC12F508 fail - Vpp problem? (Richard Rasker)
Hello,I need to reprogram an old product line containing a PIC12F508, but somehow, reading and programming fails completely, even with a completely blank, new PIC12F508 device directly connected to the PICkit 3 programmer, with no other circuitry connecte..
↧