Hello,Apologies if this isn't the board for the PICkit Serial Analyzer, but I didn't see one for analyzers. I am trying to use the PICkit's I2C Master function with LabVIEW 2014, and have a lot of VI's to wrap the latest .NET driver. The analyzer appears ..
↧
PICkit, I2C and LabVIEW (Simon Goodson)
↧
PicKit2 as programmer for 2Mbit SPI flash pm25ld020? (RDelpopolo)
Does the pickit2 support the 2Mbit SPI Flash programming, in particular the pm25ld020?I need to reprogram the bios of a video card that i messed up.Any help? Thank you...
↧
↧
PICkit 3 Device Database Missing? (johnf999)
I have just received PICkit 3 and am trying to use it with MPLAB 8.35. I get the following: PICkit 3 detected
Connecting to PICkit 3...
Firmware Suite Version...... 01.23.22
Firmware type......................PIC18F
PICkit 3 Connected.
The PICkit 3 i..
↧
PicKit3 driver problems under both Linux, XP and W7 (pnpn)
Hi all, I purchased a Pickit3 with the intention to run it under Linux. However, MPLAB IPE hangs when I start it with the PicKit3 plugged in. Therefore, I decided to first get it working under Windows. I tried on two different machines, one with XP (shame..
↧
Pickit 3 issue. Looking for HID Bootloader (btondin)
First of all, sorry for my bad english. Is not my native language Well. I've been for some hours rummaging this forum looking for solving an issue with a pickit 3 programmer. My old pickit3 died some weeks ago and microchip replaced it. But the problem is..
↧
↧
PICKIT3 - PIC32MX120F032B Memory Mismatch Error/Failed to Program Device (arrietem)
So I've been at this for a few hours now trying to figure out why the PICKIT3 won't program my PIC32MX120F032B chip. The ICSP will successfully verify that the chip is connected and erase the chip but, when programming, will run into an error. Nothing I'v..
↧
PICkit 3 and ICSP of PIC24H (Atkins)
I am getting ready to use the PICkit 3 with In-Circuit Serial Programming (ICSP) to download a booltloader firmware (p24HJ64GP502_57600baud_bootldr.hex) into my Mini-Bully PIC24HJ64GP502 microcontroller so that it can (hopefully) successfully communicate ..
↧
Windows 8.1 64-bit, MPLAB X 2.30 and PICKIT 3 not connecting to to the 44-Pin Demo board (dmac10)
Hi,I've just purchased the PIC Kit 3 with the demo board(PIC18F45K20). I've installed the MPLAB X 2.30 and the toolchains. The drivers have installed successfully as I can see the device in device manager. I've configured the project to use the correct ta..
↧
The following memory regions failed to program correctly: (davidsonlot)
I have a similar problem. My microcontroller worked perfectly, so I programmed several times (with the power of PICkit3 5V) and suddenly I got this message. (From here I can only program the FIRST time with a NEW pic) PICkit 3 detectedConnecting to PICkit..
↧
↧
Pickit2 for dsPIC30F2010 (snapdragon)
Hi, I'm using Pickit 2 to program dsPIC30f2010. Pickit2 application version is 2.61, device file version is 1.61 and OS Firmware 2.32. I could program PIC18F2550 with the same Pickit2 but not dsPIC. Please Help!..
↧
PIC16f1827 : target Device ID 0x3FE0 does not match (tadavid_dsi)
Hello, I recently bought : I try with MPLAB X IDE or MPLAB 8.91 and I have always same error message :Target Device ID (0x3fe0) does not match expected Device ID (0x27a0). I also try with an without an extern alimentation (5v) or switching the pic (I have..
↧
mistake in lesson 12 "Table look" of PICkit3 (lip01)
In lesson 12, named „Table lookup“, shipped with the PICkit3 Starterboard, is one mistake. If you try to use this lesson (in assembler), the result will be nothing: no led is lightening, no changing of potentiometer will have an affect.The failure is, tha..
↧
PIC24FJ64GB002 Programmer (NIMIT VACHHANI)
Greetings People, I have just started with PIC microcontrollers and i have written UART code for PIC24fj64gb002 to start with. I want to know whether the universal programmer that i use to program my Atmel 89S8253 micro controller will work for PIC24fj64g..
↧
↧
PicKit3 PIC32 programming speed. (phillhs)
Hi all, I don't know if I have a problem with my setup or things can be improved, but the time it is taking to program a PIC32MX170 seems very long, about 35 seconds, of which the first couple are the program build and the rest seems to be the actual prog..
↧
I can't program with pickit 3, mplab x ide using linux, pic16f628a (and also pic18f4550) (newtonis)
Hi to all this is my first post here :)
I bought 1 year ago a pickit 3 programmer. I used it to program two different microchips, pic16f628a and pic18f4550 (always with MPLAB X IDE and xc8 compiler). It worked perfectly, and also I used the debugger wi..
↧
picKIT3 support for microtrollers 16C57 and 16F57 (antoniovidal)
Hi,I am new to Microchip and would like to understand which is the best tool for programming/debugging the 16C57 and 16F57 microcontrollers. The PicKit3 seems to be a good start, but I cannot find a list of the supported controllers, for PicKit3. BR,..
↧
Intermittent programming success with PickIt3 (Dave0651)
I've seen several posts relating to problems with the PickIt3 and MPLABX but none of the solutions seem to fit my problem. I have one version of code that can always be programmed correctly and a later version that sometimes can be programmed correctly. W..
↧
↧
PIC16F88 problem (Toley)
I have 10 PicKit2 programmers (I'm in a school) they all use V2.40 with latest firmware. I also have a PicStart Plus programmer with a PUM module, also with the latest firmware. They all have the same problem with PIC16F88. When they are new I'm able to p..
↧
Target Device ID does not match expected Device ID (mr.duck)
Ok, so im new to pic programming, but i had my PIC16F628A hooked up to my PICKIT3 flasher according to the circuit outlined here: http://ww1.microchip.com/downloads/en/DeviceDoc/MPLAB_ICD3_Poster_51765a.pdf As can be seen in there, there are no bypass cap..
↧
Incrementing a serial number (Laz7)
Is there a production programming tool for the PIC16LF family (16LF1825 in this case) which allows for auto-incrementing a serial number in Flash or EEPROM? TIA.Laz..
↧