USB Driver for MPLAB PM3 (Durite)
I have installed MP X IDE 3.05 IPE, but cannot seem to find the drivers for the PM3, I have also tried installing the IDE as well but still no drivers seem to be present. All the searches I have done...
View ArticlePicKit4 tools (Izseko)
Hello, Question is about new PicKit4 and available commands. In our serial production we still using PicKit3 with PK3CMD, however sooner or later we must upgrade our production line. Is there any...
View ArticlePICkit3/4 programming via the ipecmd.jar command on a ARM based...
We have been running a Windows 7/10 based Python program that calls the ipecmd.jar method for programming our controllers via a PICkit3 or 4: "java.exe" -jar "ipecmd.jar" -TPPK3 -E -M -P18F67K22...
View ArticleHow tp limit the program count for PicKit3 programmer to go (leanid)
Hello, I need to arrange firmware update on the customer side. My plan was to send PicKit3 in Programmer-to-go mode to the customer. But I need to limit program count.Is there way how to do this? My...
View Articleis there a ISP cable for the ATF22V10 device? (fcbartra)
Please email me part numberThank youFausto Bartra..
View ArticlePCB panel programming (Jay Tronics)
Hello, I have been tasked to design a rig that will program a panel of PCBs using the PM3 programmer. My question is, if I were to take all the programming headers of each PCB and had them routed...
View ArticlePM3 ICSP Cable, info on connector (lslonim@our3cats.com)
Hi, I am using a PM3 programmer. I'd like to make a custom cable to replace the MPLAB PM3 ICSP Cable that I am using with it. I tried a ribbon cable connector and it didn't fit the plug end on the...
View ArticleAC164393 - PM3 Universal Socket Module 8uDFN(2x3x0.5)mm problem (kladek)
Hi, i tried to program a PIC12LF1552T-I/MU controller with PM3 and universal socket module, but it failed. The programmer says that the controller does not support and suggest an another socket. Can i...
View ArticlePICKIT 3.10 - Issues programming PIC12F683 (ismurdegus)
Hi guysThanks for reading my post. I am new of the forum and of the Microchip environment. I need some help and I will try to give as much info I can... #Pickit 3 - Version 3.10#pic12F683-I/P#Windows 7...
View ArticleMPLAB & PicKit2 stopping execution after programming or reading EEDATA...
Is there any way to stop my 12F675 EEDATA memory from being overwritten by my programming execution starting while the part is in the programming socket? I am saving readings to EEDATA in my programme...
View ArticlePICKIT3 GETS DAMAGED AGAIN AND AGAIN (Gautya)
I am using mplab IDE v 8.70.I am programming pic18f67k22 using mplab c18 v8.70 This is the third time I have got following error while trying to program pic PICkit 3 detected Connecting to PICkit 3......
View ArticlePICkit3 not programming highest 16 words of 16F1703 (RobertW)
I've noticed there are some problems that have been reported where the last few words of program memory fail to program on some PICs, but I haven't seen any reports of this happening with the 16F1703...
View ArticlePICKIT4 died, 2 months away for a replacement, help me fix mine (encoad)
Hi All, Not sure what happened, but one day my PICKIT4 stopped working. It can no longer program. Microchip says they'll send a replacement, but they are backordered until sometime in May, which is a...
View ArticlePIC16F76 (mypic16)
I have a PIC16F76 I would like to program and need a cheap programmer. I was looking at the Pickit 2, but noticed the PIC16F76 is not in the list of supported devices. Is this true? Thanks Dana..
View ArticlePickit 2 (kgmano)
Helo,How to add PIC18F46Q10 to Pk2Devicefile? I have Pk2Devicefile ver. 2.63.212 from PICKIT PLUS. But it is not working. Please suggest how to use PICkit2 Device File Editor soft. Thanks. kgmano..
View ArticlePickit3 debugger problem on 18f devices help please ... (Thegoodlookingbloke)
I am using MPLAB IDE latest version and have updated the chip from 16f887 to 18f4685 but have come across a problem that was on a forum 10 years ago regarding a debug problem with Pickit3 on 18f...
View ArticleBlank display on MPLAB PM3 (REFA)
Does anyone in this forum know of a solution? The problem is that my PM3 no longer shows anything on the display itself (there is light on the display). There is nothing changing on my setup and my PM3...
View ArticleWill Grounding PICKit3 ICSPCLK Pin Damage Programmer (grinchy95)
Hi, I am working on a project that uses programming pins as gpio inputs and outputs with a small PIC16F18313 microcontroller. The ICSPCLK pin on the microcontroller is used in weak pull-up mode with a...
View ArticlePickit3 Issue with simple PIC24LJ118GA204 circuit (Ian Steward)
I have been using Pickit3 for a couple of years without any issues. I created a very simple circuit (attached) that ignites an LED. Initially I used the PIC24 Curiosity Dev Board (DM240004 -...
View ArticleWhich programmer is recommended? (vinyl_theif)
Hi all.I'm presently still using a Picstart Plus to program my pics (I write my programs in mplabX & then import the hex file into mplab IDE 8.9 to program, but now wish to upgrade to use some...
View Article