MPLAB PM3 and Linux (swmcl)
Hi, How 'production ready' is the PM3 on Linux? Is it a completely foolproof solution or are there a number of outstanding issues? There is a major cost involved so I would appreciate an honest...
View Article"Unhandled Exception" Error in PICkit 3 Programmer (Viswak RK)
Hi, I have been trying to program a development board using PICkit 3 Programmer and everything went right till this error popped out. Using PIckit3 programmer, when i try to connect to the PICkit3, it...
View ArticlePickit 3 help with PIC 18f4680 (shawnpwest)
I bought a Pickit 3 with the sole purpose of building something I found online. I've built the circuit boards, have the necessary components and the microcontroller. The one problem I have and haven't...
View Articlepicdem with pickit3 and 24lc16b (karl sweeney)
I'm trying to program the device using the pickit 3 and the software pickit3 v3.10The pickit pins are connect to the following for the chip. pickit device1 1,2,3 2 8 3 4 4 5 5 7 6 6 where am i going...
View ArticlePICKit 3 Stopwatch (unit?) (jokogarcia)
I set up a stopwatch between a couple of breakpoints, and I get the following response on the "Output tab" Stopwatch cycle count = 37544934(decimal) Target halted Wich is great, except I don't know...
View Articlewhat the heck do i have to do to get a PK3 to work? (another voltage issues...
Hi,this is another voltage issues on the pk3 thread/rant, because i wasn't able to find a solution this time.so, what's happening today?PK3 is correctly connected to the mcu (MCLR, VDD, VSS, PGC, PGD)....
View ArticlePICKIT 3 VPP Hardware Problem? (UT_Tech)
Hi All, I have a PICKIT3 programmer that mysteriously stopped working with the symptom of "Target Device ID (00000000)" on any target board, ext power or not, including target boards that work fine...
View ArticlePickit 3 Standalone programmer problem (roxy1001)
I am trying to program pic18f45k22 using pickit3 standalone programming software and pickit3 module.PIC is not responding at all after I use pickit3 programming software. Code is running fine when I...
View ArticleProgrammer starts too slow (moeller)
Dear all, after build the IDE takes 35 seconds to start the programming of the device.I am unsing 33FJ64MC804, MPLAB X v2.35 (v2.10 = same problem) , Win7.I have tried REAL ICE and ICD3, no difference....
View ArticlePM3CMD help (1insuare)
Hi, I´m trying to use PM3CMD for PIC programming in great batches. My trouble is that every device must have a different firmware (hex). I created a c# program to generate new hex files and program...
View ArticleNeed to program PIC24FJ128GB202 with standalone Pickit2 (zijo)
I looked Pickit2 data file editor but only information that I can change is devices ID.For example I looked file for PIC24FJ128GB106 which should be similar, but there are values for configmask and...
View ArticlePicKit3 and PIC24FV16KM202 (mattiatech)
Dear community, I have a problem for programming a PIC24FV16KM202 with a PicKit3. The PIC24FV is mounted on the Microstick for 5V PIC24 K-SERIES (DM240013-2). For developing the application on the...
View ArticlePICkit 3 Low Pin Count Demo Board schematics error? (pickme)
Greetings,This is probably a question to manufacturer/design of PICkit 3 low Pin Count Demo Board. (See ) The schematics indicates that R7 resistor value is 1 Kohms or one kilo-ohms. However, when I...
View ArticleHelp for new PIC32 configuration, what to buy ? (Ulysse)
Good morning, I need some help to do the right choices in my new PIC32 configuration (I uses a USB starter kit II for 2 years ago). In order to design a better PCB, I decided to work with a PIC32MZ...
View ArticlePickit3 problem (drieran)
Hi, I developed an empty project for a PIC16LF1823 with last version of MPLAB X. Basically enables RC2.Using pickit 3 I flash the firmware and runs correctly. I know because if I enable RC2 then turn...
View ArticleHow to turn off picit 3 programmer using labx (pickme)
Greetings,I noticed that lab 8 has a feature ( button) that allows user to turn off board when connected to pickit 3. Does the labx have the same feature that allows to turn off the board before...
View ArticlePickit3 (clone) problem (treguy)
Hi, I bought a pickit3 clone from aliexpress (I just can not afford the price of a real one + shipping). I manage to program a pic16f1455 once, it was verified, but then when I want to program it...
View ArticlePICKIT3 and LVP - Is It Supported (AssemblyJunkie)
I have been using PICs now since my purchase of the PICstart Plus in 1994. I have designed mixed signal ASIC for 14 years now an know my way around this stuff. My question is very, very specific. I...
View ArticleHooking up the PM3 on an Ubuntu 14.04.1 guest VMware VM on Ubuntu 14.04.1...
Hi, Advice needed here ... things are looking decidedly unhelpful. I'd like to connect the PM3 and check that it works. I'd also like to make sure the PM3 is at the latest firmware build. Any tips ?...
View ArticleProgramming does not complete (jvh)
Programming via the PICkit 3 was working fine earlier today. Now when it starts programming the status flickers for a bit then goes green and stays green but the PICkit 3 window still says...
View Article