Pickit 3 Debug problem (Avicente)
Hi, first of all I've to say I'm newbie programming PIC's. I'm doing my bachelor degree abroad and it consist of mesuring a magnetic field with a mag3110 sensor connected to a pic 18F26k22 uC via i2c...
View ArticleMisprint in PICkit 3 Setup Poster? (FranciscoB)
Hello,I bought the product PICkit 3 and in the poster (PICkit 3 setup poster) indicates that the resistance between Vdd and MCLR of the Target Application PC Board, must be 50 K while in the user...
View ArticlePicStart Plus. (Hairyloon)
I've been given an old PicStart Plus programmer with the intent to learn PIC programming, but I have discovered that it is obsolete: not only is it incompatible with the current version of MPLab, it...
View ArticleProblem with PICKIT-3 (amtech)
Dear sir, We are using dsPIC33EP512MC506 controller for motor control application .When i dowanload the program using PICKIT-3 in MPLAB X IDE at that time it shows error as below: Connecting to MPLAB...
View ArticlePK3CMD Preserve EEPROM (mangozac)
Hi all, OK so that our client can make updates to software in some products I decided to get some PICKit3s (one for the client, one for me). The idea is to use PK3CMD so that the client does not need...
View ArticleMPLAB v5.70.40 doesn't recognize PCSTART Plus (Tecnitower)
I had a PICSTART Plus programmer working with MPLAB v5.70.40 on Windows XP (don't judge me... it's what i recieved) and the person who was programming put a PIC 12F629 in a bad position, from the...
View ArticlePICKit3 Debug basics (DaveTheHacker)
Ok, I'm trying the easy way to play. (the old remove chip, program, replace chip, crash, repeat is getting old)(I'm also just getting back into uC's after quite a few years so bear with me. MPLAB IDE...
View ArticleHow can I set up communication with my PICSTART Programmer? (Ken Sookhoo)
I have used my PICKSTART Programmer (Model R9) successfully many times in the past. I am now presently trying to use it again but neither of my present computers have a COM port. I have been able to...
View ArticlePickkit3 programming pic32mx795L (Fuchz)
hallo, i have made a printed circuit Board with a pic32mx795F512L and i try to Programm the mcu using the PICKKIT3. MCLR is vs 10K Pull Up at VDD = 3V3. PIN 2 via 100nF at VDD. PIN 3 to GND. PIN 4 to...
View ArticleAdding PIC12F1572 to PICkit2 device file (PG)
Hello, I tried to add the PIC12F1572 to the PICkit2 device file but it seems that doesn't work: I'm using the PICkit2 programmer v2.61 and when I connect the programmer to the PIC12F1572 (I checked the...
View ArticlePicKit3 stopped working! (hjf)
I recently installed MPLAB X 2.30 and suddenly my PICKit3 no longer works.I was about to program a PIC18F46K20 and it started downloading the operating system, and then it failed and all it does is...
View ArticleI just want to read the EEPROM. Inexperienced PIC user. (viored)
Hi, So my bosses just handed me a project involving a PIC which I have no experience with. I've been reading guides and tutorials, but I haven't found anything remotely useful. So here's my problem. I...
View ArticleReburn Picstart Plus "10-00379-r3" bootloader.. wich hex file should I...
Hi!I have a Picstart Plus unit, 10-00379-r3, That I cant seem to communicate with.The internal voltages are ok, and the power led lits up, but not activity led.Tried 3 different laptops with and...
View ArticlePICKit3 - Pile of rubbish? (crosland)
Brand new PICKit3, Windows 8.1 MPLAB IDE 8.90.Target board works fine with a PICKit2 so no problems there. Using the same short cable between the PICKit and the target.First thing it wants to do is...
View ArticleMass program loading to pic chips (Willsonbk)
Dear All I would like to check you all experience programmer, I have Qty 500 pic chips and i will like to upload my firmware to it but is the are good solution to program all of pic chips fast instead...
View ArticlePicStart Plus. (mcj7247)
I have an older R14 Pic Start Plus Progammer (Software V2.30) that I had been using with an old PC (Win 95), MPLAB IDE V5.?? and PIC Basic Compiler. I am doing a new project with a PIC16f628 and a PIC...
View ArticlePICKIT3 & MPLAB X require debugging header (Alon Boico)
hi, i am using pic18f14k50 and i am trying run with debug mode.i get an error that i need a debugging header.what is that debugging header?do i need this header or can i bypass it?..
View ArticlePickit 3 programmer-to-go EEPROM (Misc)
hi, is it possible to preserve the EEPROM memory in programmer-to-go mode of PicKit 3? somehow in mplabx you can select that eeprom section should not be written, but still it seems to be completely...
View ArticleTwo questions about the PICkit Serial Analyzer. (DominusT)
Hi. Does PICkit Serial Analyzer is useful for analyzing signals whose voltage level are 3.3V? I'm thinking of buying one but I see that it's a relatively old tool. Is there the possibility that a...
View Articlemplab_ipe didnt find pickit 3 (schlabs)
Hi, I am frustrated, i read all that i can find about pickit 3 comunication and no success. I am running an Linux 64 opensuse 11.0. I am using SUCCESSFULLY the following programers:Picstart plus (...
View Article