Pickit programmer-to-go and circuit voltage (giuseppe83)
Hi to all, I would try to use Pickit 3 programmer-to-go on a circuit that is powered by 3.3V. On to-go modality can I specify the power supply that Pickit 3 must provide? For example 3.3V. Or only 5V...
View ArticleA quick Thank You to Microchip for the PICkit 3's Programmer to Go feature......
I have to say, PTG is a VERY convenient feature. I needed to update the firmware in an installed board, and was searching around for a utility that would take the image and run the PICkit 3 without...
View ArticleProgrammer to Go erases EEPROM when it should not (dmitrik1)
Hi All I have problem with the PICkit3 "Programmer to Go" feature programming the device dsPIC30F5011.MPLAB ver 8.86. The programmer setting is: Programming EEPROM box is un-ticked and preserve EEPROM...
View ArticleIs my week old PICKIT 3 dead? (BobK)
I have started a new project, using dsPIC33EP256MC504. Previously, I was happy with my PICKIT 2 and MPLAB 8, and C30. But for this project I had to upgrade to PICKIT3, MPLABX, and XC16. I am pretty...
View ArticlePIC Multi-Task (Wow)! (Ajioz)
Hi everyone, I am working on house automation, while am yet to make a good choice of the best Pic to use, I think i hace a major challenge. Below is my source code. Target chip for now is PIC16F877A. I...
View ArticlePICKit 3 getting stuck (Oldevel)
I am attempting to debug the following code as a single file project on a "PIC16F631/677/685/687/689/690 Series" MCU, using a PICKit3 and MPLAB X v1.95. ; ProgramOrg 0x0000 MOVLW 0x00 MOVWF PCLATH GOTO...
View ArticleMPLAB ICD3 does not identify dsPIC33EP512GP806 (marcosartore)
Hello,I am trying to program a dsPIC33EP512GP806 on a custom board. When the board is connected to the ICD3 MPLAB shows the following error:Target Detected - ICD3Err0086: Target Device ID (043d0000)...
View ArticleMy ICD3 is killing my MCP2551 CAN transceiver! (Heliophage)
Okay, here is something really puzzling. Today, I checked a new version of a product development board using an 18F2580 microcontroller and an MCP2551 CAN transceiver. It powered up just fine and VCC...
View ArticlePickit3 no connect with Mplabx (Chaco89)
Hello everyone!I´ve tried to connect pickit3 with Mplab X IDE v 2.20, i´m working on C30 and i want debug a program for dsPICFJ128GP802.I´ve download application pickit3 v3.01 and and programming my...
View ArticlePM3 power suppy cable (barber)
The connector on the cable that goes from the power supply to the PM3 has a broken pin. I have not been able to find a replacement on the Microchip site. Does any one know of a source for the cable?..
View ArticleGetting started with Pickit 2 and MPLAB X (Droidling)
I bought a Pickit 2 starter kit a few years back. At the time I was able to program it and ran through a few demo projects. It sat in a closet since then. I now have a project that I want to use a...
View ArticlePK2Error0027: Failed verify with PIC18F44J10 (zlanczky)
I'm quite beginner in PIC progamming, but have some experience with PIC16 family 5V processors. Now I plan to progam a PIC18F44J10 with Pickit2. The connect to device is successful:Found PICkit 2 -...
View ArticleSoftware for production programming ? (MPLAB IDE, IPE ?) (emirc)
Hi, Which software should be used for production programming of PIC with ICD3 ? The MPLAB IPE functionnalities suit for this, but IPE is still in beta version and it can not be installed without MPLAB...
View ArticleDifferences between production and development programmers (aurelienr)
Hello, I'm working on a project for a customer that request the capability to modify a table of values in memory (EEPROM or FLASH) several years after the development. I have thought that a simple...
View ArticlePM3 Buzzer (mvakil)
Can the PM3 buzzer be setup to buzz when programming is complete in stand alone mode? I have a SD card with an environment but when the user programs a device there is no buzzer indication that...
View ArticlePM3CMD: command file doesn't program in right way (emanuelebelpanno)
Hello everyone, I have a problem using a command file: I created a file batch and when I click double the file batch, the pm3 program starts. I see these steps in the pm3 display:- receiving file;-...
View ArticleIssue in program PIC24EP512GU810 use Pickit3 (Hai Hoang)
I have some PIC24EP512GU810, tried on Mplabx, Mplab IPE and Mplab V8, Pickit3 detected the chip, it's ID = 4002, Pickit3 can erase, blank check but can not program with the chip. Anyone can tell me...
View ArticleTrying to make use of LIN serial analyzer... (Taku)
I'm very beginner in this forum. Also, very beginner of microchip products. I'm not sure I should post it here. If this post is not appropriate here, please let me know. I need to create a LIN...
View ArticlePICkit3 PIC32MZ2048ECH100 memory mismatch error (SilverOT)
Hey Hope someone can help me out with a problem I'm having with the PIC32MZ2048ECH100 and the PICkit 3. More exactly I have the MA320012 add on board wired up to the PICkit 3. I've added a 10k resistor...
View ArticlePICkit3 Lessons Need Updating (XK8)
I have completed all 12 Lessons (DV41370C) on my PICkit3 using MPLAB IDE 8.92 and MPLAB C18 v3.40 Compiler.As this is now 'legacy' software I have upgraded to MPLAB X IDE and MPLAB XC8 C Compiler as...
View Article